MCP2030-I/ST Microchip Technology, MCP2030-I/ST Datasheet - Page 3

• Manufacturer Part Number: MCP2030-I/ST
• Description: IC KEYLESS ENTRY AFE 14TSSOP
• Manufacturer: Microchip Technology

Specifications of MCP2030-I/ST

• Rf Type: ISM
• Frequency: 125kHz
• Features: 10kbps
• Package / Case: 14-TSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

1.0
Absolute Maximum Ratings
Ambient temperature under bias...................-40°C to +125°C
Storage temperature .................................... -65°C to +150°C
Voltage on V
Voltage on all other pins with
respect to V
Maximum current out of V
Maximum current into V
Maximum LC Input Voltage
(LCX, LCY, LCZ) loaded, with device........................ 10.0 V
Maximum LC Input Voltage
(LCX, LCY, LCZ) unloaded, without device............. 700.0 V
Maximum Input Current (rms) into device
per LC Channel.............................................................10 mA
Human Body ESD rating ....................................2000 (min.) V
Machine Model ESD rating ..................................200 (min.) V
DC Characteristics
© 2005 Microchip Technology Inc.
Electrical Specifications: Standard Operating Conditions (unless otherwise stated)
Operating temperature
LC Signal Input
Carrier Frequency
LCCOM connected to V
Supply Voltage
V
Power-on Reset signal
Modulation Transistor-on Resistance
Active Current (detecting signal)
1 LC Input Channel Receiving Signal
3 LC Input Channel Receiving Signals
Standby Current (wait to detect signal)
1 LC Input Channel Enabled
2 LC Input Channels Enabled
3 LC Input Channels Enabled
Sleep Current
Analog Input Leakage Current
Digital Input Low Voltage
Digital Input High Voltage
Digital Input Leakage Current (Note 1)
SDI
SCLK, CS
Digital Output Low Voltage
ALERT, LFDATA/SDIO
Digital Output High Voltage
ALERT, LFDATA/SDIO
Digital Input Pull-Up Resistor
CS, SCLK
Note
DD
Start Voltage to ensure internal
1:
*
†
ELECTRICAL SPECIFICATIONS
SS
DD
These parameters are characterized but not tested.
Data in “Typ” column is at 3.0V, +25 C unless otherwise stated. These parameters are for design guidance only and are not tested.
Negative current is defined as current sourced by the pin.
Parameters
...................................... -0.3V to (V
with respect to V
SS
DD
LCX, LCY, LCZ
SS
-40 C
Sinusoidal 300 mV
125 kHz
pin ....................................250 mA
pin .................................300 mA
LCCOM
SS
T
A
............... -0.3V to +6.5V
+85 C
(†)
I
I
Sym.
V
STDBY
SLEEP
V
I
V
R
V
I
V
R
ACT
V
PP
POR
I
AIL
DD
OH
IL
OL
PU
IH
M
IL
V
0.8 V
DD
DD
Min.
V
2.0
50
—
—
—
—
—
—
—
—
—
—
—
—
—
SS
+ 0.3V)
- 0.5
DD
PP
PP
Typ†
200
3.0
0.2
50
10
13
—
—
—
—
—
—
—
—
—
2
3
4
V
† Notice: Stresses above those listed under “Maximum
Ratings” may cause permanent damage to the device. This is
a stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operation listings of this specification is not implied. Exposure
to maximum rating conditions for extended periods may affect
device reliability.
0.3 V
SS
Max.
V
100
350
3.6
1.8
18
—
—
5
6
7
1
DD
+ 0.4
1
1
1
1
DD
Units
k
V
V
V
V
V
V
A
A
A
A
A
A
A
A
A
A
V
CS = V
Input = Continuous Wave (CW);
Amplitude = 300 mV
All channels enabled.
CS = V
CS = V
V
ground. Internal tuning capacitors are switched
off, tested in Sleep mode.
SCLK, SDI, CS
SCLK, SDI, CS
V
V
V
Analog Front-End section
I
I
V
OL
OH
DD
DD
DD
SS
PIN
DD
= 1.0 mA, V
= -400 A, V
= 3.0V
= 3.6V, V
= 3.6V
= 3.6V
V
V
DD
DD
DD
PIN
DD
; ALERT = V
; ALERT = V
V
SS
DD
DD
MCP2030
DD
Conditions
V
= 2.0V
IN
= 2.0V
PP
DD
DD
.
1V with respect to
DS21981A-page 3