ISL76683AROZ-T7 Intersil, ISL76683AROZ-T7 Datasheet
ISL76683AROZ-T7
Specifications of ISL76683AROZ-T7
Available stocks
Related parts for ISL76683AROZ-T7
ISL76683AROZ-T7 Summary of contents
Page 1
... GND ISL76683 FIGURE 1. BLOCK DIAGRAM CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 Intersil (and design trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners COMMAND REGISTER DATA ...
Page 2
... SDA I C serial data Ordering Information PART NUMBER (Notes ISL76683AROZ-T7 NOTES: 1. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020 ...
Page 3
... Thermal Resistance (Typical ODFN Package (Notes Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+105°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +105°C DD Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +105°C Pb-free reflow profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp = 3V +25° 100k Ω 1% tolerance, unless otherwise specified, Internal Timing Mode A EXT CONDITION Software disabled, -40° ...
Page 4
Electrical Specifications V DD Operation (see “Principles of Operation” on page 6). (Continued) PARAMETER DESCRIPTION I SDA Current Sinking Capability SDA I INT Current Sinking Capability INT NOTES: 6. Compliance to datasheet limits is assured by one or more methods: ...
Page 5
Typical Performance Curves 1.015 1.010 5000 lux 1.005 1.000 200 lux 0.995 0.990 2.0 2.3 2.6 2.9 SUPPLY VOLTAGE (V) FIGURE 6. OUTPUT CODE vs SUPPLY VOLTAGE 330 320 310 300 290 280 270 260 -60 ...
Page 6
Principles of Operation Photodiodes The ISL76683 contains two photodiodes. Diode1 is sensitive to both visible and infrared light, while Diode2 is mostly sensitive to infrared light. The spectral response of the two diodes are independent from one another. See Figure ...
Page 7
Start DEVICE ADDRESS DATA SDA SDA SDA DRIVEN BY MASTER Out CLK ...
Page 8
Register Set There are eight registers that are available in the ISL76683. Table 1 summarizes the available registers and their functions. ADDR REGISTER (HEX) NAME BIT(S) 00 Command 01 Control 02 Interrupt Threshold HI 03 Interrupt Threshold LO 04 LSB_Sensor ...
Page 9
TABLE 2. WRITE ONLY REGISTERS REGISTER ADDRESS NAME b1xxx_xxxx sync_iic Writing a logic 1 to this address bit ends the current ADC-integration and starts another. Used only with External Timing Mode. bx1xx_xxxx clar_int Writing a logic 1 to this address ...
Page 10
Range/Gain; Bits 3 and 2. The Full Scale Range can be adjusted by an external resistor R EXT 2 adjusted via I C using the Gain/Range function. Gain/Range has four possible values, Range(k) where through 4. ...
Page 11
Gain/Range, Range (k) The Gain/Range can be programmed in the control register to give Range (k) determining the FSR. Note that Range(k) is not the FSR (see Equation 3). Range(k) provides four constants depending on programmed k that will be ...
Page 12
INTEGRATION TIME IN EXTERNAL TIMING MODE This timing mode is programmed in the command register 00(hex) bit 5. External Timing Mode is recommended when integration time can be synchronized to an external signal (such as a PWM) to eliminate noise. ...
Page 13
1,000 I C clock cycles. An external sync_iic command sent I C 1,000 cycles after another sync_iic command rejects both 60Hz and 50Hz AC noise signals. Next, is ...
Page 14
... Since ambient light sensor devices do not dissipate high power, heat dissipation through the exposed pad is not important; instead, similar to DFN or QFN, the exposed pad provides robustness in board mount process. Intersil recommends mounting the exposed pad to the PCB, but this is not mandatory. ...
Page 15
TO 3. SLAVE_0 1 VDD SDA 2 GND SCL REXT 4.7µF 0.1µF REXT ISL76683 100k 15 ISL76683 10k 10k RES1 SLAVE_1 6 SDA 5 SCL 4 INT ...
Page 16
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. ...
Page 17
Package Outline Drawing L6.2x2.1 6 LEAD OPTICAL DUAL FLAT NO-LEAD PLASTIC PACKAGE (ODFN) Rev 2, 6/10 2.10 6 PIN 1 INDEX AREA (4X) 0.10 TOP VIEW 2.50 PACKAGE OUTLINE 2.10 0.65 (4x0.65) (6x0.30) (6x0.55) TYPICAL RECOMMENDED LAND PATTERN 17 ISL76683 ...