PBA-1 BANNER ENGINEERING, PBA-1 Datasheet - Page 8

• Manufacturer Part Number: PBA-1
• Description: Photoelectric Sensor
• Manufacturer: BANNER ENGINEERING

Specifications of PBA-1

• Supply Voltage Max: 130VAC
• Switch Terminals: Screw
• Supply Voltage Min: 105VAC
• Frequency, Operating: 50⁄60 Hz
• Function: Module, Power Block
• Technology: Photoelectric
• Lead Free Status / Rohs Status: RoHS Exempt Product

8
MULTI-BEAM
NOTE: for detailed information on
available retroreflective materials, see
the Banner product catalog.
RETROREFLECTIVE
Mode
Sensing Mode
OBJECT
RETRO
TARGET
SBL1
Range: 1 in. to 30 ft.
(2,5cm to 9m)
Response: 1ms on/off
Repeatability: 0.3ms
Beam: infrared, 940nm
SBLX1
Range: 10 to 75 ft. (3 to
22m) with one BRT-3 target;
10 to 100 ft. (3 to 30m) with
three BRT-3 targets
Response: 10ms on/off
Repeatability: 1.5ms
Beam: infrared, 880nm
SBLV1
Range: 6 in. to 30 ft.
Response: 1ms on/off
Repeatability: 0.3ms
Beam: visible red, 650nm
SBLVAG1
Range: 12 in. to 15 ft.
Response: 1ms on/off
Repeatability: 0.3ms
Beam: visible red, 650nm
SBLV1: visible beam makes alignment very easy, and is the first choice for most retroreflective applications.
Not for use in dirty environments; rather use opposed mode or see SBL1 & SBLX1, below. Do not locate
retroreflector closer than 6 inches (15cm) from sensor.
SBLVAG1: uses anti-glare filter for immunity to direct reflections from shiny objects. Use only with models
BRT-3 or BRT-1.5 retroreflective targets. Use only in clean environments. Do not locate retroreflector closer
than 12 inches (30cm) from sensor.
SBL1: use where invisible beam is advantageous (e.g. security applications or film processing). First choice for
retroreflective sensing in slightly or moderately dirty environments. Do not use when the object to break the
beam has a shiny surface, unless the angle of light to the surface can be predicted.
SBLX1: highest gain available in a retroreflective sensor. Use for all applications requiring more than 30-foot
range where opposed mode sensors cannot be used. Objects must pass at a distance of at least 10 feet from the
sensor to be reliably sensed.
3- & 4-wire Scanner Blocks
Models
(0,15 to 9m)
(0,3 to 4.5m)
E
X
C
E
S
S
G
A
I
N
E
X
C
E
S
S
G
A
I
N
E
X
C
E
S
S
G
A
I
N
I
I
I
E
X
C
E
S
S
G
A
I
N
1000
1000
I
1000
1000
100
100
100
100
10
10
10
10
1
.1 FT
.1 FT
1
.1 FT
1
1
1 FT
Excess Gain
with one
BRT-3 3"
reflector
with BRT-1 1"
reflector
with BRT-1 1"
reflector
SBLV1
SBL1
1 FT
1 FT
1 FT
10 FT
DISTANCE
DISTANCE
with
BRT-T
tape
DISTANCE
DISTANCE
with
BRT-T
tape
SBLVAG1
SBLX1
with three
BRT-3 3"
reflectors
100 FT
10 FT
10 FT
with BRT-3 3"
reflector
10 FT
with BRT-3 3"
reflector
1000 FT
100 FT
100 FT
100 FT
I
N
C
H
E
S
I
N
C
H
E
S
I
N
C
H
E
S
I
N
C
H
E
S
0
0
30
20
10
0
10
20
30
0
3
2
1
1
2
3
6
4
2
2
4
6
6
4
2
2
4
6
Beam Pattern
0
0
0
0
DISTANCE TO REFLECTOR--FEET
SBL1
SBLV1
DISTANCE TO REFLECTOR--FEET
DISTANCE TO REFLECTOR--FEET
DISTANCE TO REFLECTOR--FEET
SBLX1
6
3
6
25
SBLVAG1
12
6
12
50
with one BRT-3 reflector
with BRT-3 reflector
with BRT-3 reflector
with BRT-3 reflector
75
18
18
9
100
24
24
12
125
32
32
15