HSDL-3208-021 Lite-On Electronics, HSDL-3208-021 Datasheet - Page 2

• Manufacturer Part Number: HSDL-3208-021
• Description: Infrared Transceivers IR Transceiver 115Kb/s
• Manufacturer: Lite-On Electronics
• Type: TX/RXr

Specifications of HSDL-3208-021

• Wavelength: 875 nm, 880 nm
• Continual Data Transmission: 115.2 Kbit/s
• Radiant Intensity: 8 mW/sr
• Half Intensity Angle Degrees: 30 deg to 60 deg
• Pulse Width: 4 us, 1.6 us
• Maximum Rise Time: 50 ns, 600 ns
• Maximum Fall Time: 50 ns, 600 ns
• Led Supply Voltage: 0 V to 6.5 V
• Maximum Forward Current: 50 mA
• Operating Voltage: 2.4 V to 3.6 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: - 25 C
• Dimensions: 7.4 mm x 2.9 mm x 1.8 mm
• Data Rate: 115.2Kbps
• Peak Wavelength: 875/880nm
• Angle Of Half Sensitivity: 60/30°
• Fall Time: 600/50ns
• Rise Time: 600/50ns
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (min): 2.4V
• Operating Supply Voltage (max): 3.6V
• Mounting: Surface Mount
• Pin Count: 7
• Operating Temp Range: -25C to 70C
• Operating Temperature Classification: Commercial
• Idle Current, Typ @ 25° C: 100µA
• Link Range, Low Power: 30cm
• Operating Temperature: -25°C ~ 70°C
• Orientation: Side View
• Shutdown: *
• Size: 7mm x 2.8mm x 1.6mm
• Standards: IrPHY 1.4
• Supply Voltage: 2.4 V ~ 3.6 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

2
Application Support
Information
The Application Engineering
group in Lite-On Technology is
available to assist you with the
Order Information
Marking Information
The unit is marked with ‘YWL’ on the back of the PCB for front option
without shield.
Y = year
W = work week
L = lot information
I/O Pins Configuration Table
Notes:
1. This pin can be connected directly to V
2. Leave this pin unconnected.
3. This pin is used to transmit serial data when SD pin is low. Do not float the pin. This pin has an internal 500 k pulldown with a typical input
4. This pin is capable of driving a standard CMOS or TTL load. No external pull-up or pull down resistor is required. It is in tri-state
5. The transceiver is in shutdown mode if this pin is high. Do not float the pin.
6. Regulated, 2.4 to 3.6 volts.
7. Connect to system ground.
Recommended Application Circuit Components
Notes:
8. CX1 must be placed within 0.7 cm of the HSDL-3208 to obtain optimum noise immunity.
9. In environments with noisy power supplies, supply rejection performance can be enhanced
Part Number
HSDL-3208-021
Pin
1
2
3
4
5
6
7
Component
R1
CX1
CX2
capacitance of 2 pF.
mode when the transceiver is in shutdown mode. This pin tristates with a weak 500 k
by including CX2, as shown in “Figure 1: HSDL-3208 Functional Block Diagram” in Page 1.
Symbol
LED A
LED C
TXD
RXD
SD/Mode
V
GND
CC
Recommended Value
30
0.47 F 20%, X7R Ceramic
6.8 F 20%, Tantalum
Packaging Type
Tape and Reel
5%, 0.25 Watt for 2.4 <= V
Description
LED Anode
LED Cathode
Transmit Data
Receive Data
Shutdown
Supply Voltage
Ground
CC
(i.e. without series resistor) at less than 3 V.
technical understanding
associated with HSDL-3208
infrared transceiver module. You
can contact them through your
local Lite-On sales representatives
for additional details.
Package
Front View
CC
<= 3.6 V
I/O Type
Input
Input, Active High
Output, Active Low
Input, Active High
Supply Voltage
Ground
Quantity
2500
Notes
8
9
pullup resistor.
1
2
3
4
5
6
Notes
7