LAN91C100FD-SS SMSC, LAN91C100FD-SS Datasheet - Page 31

• Manufacturer Part Number: LAN91C100FD-SS
• Description: Ethernet ICs Non-PCI 10/100 Ethernet MAC
• Manufacturer: SMSC
• Type: Single Chip MAC and PHYr

Specifications of LAN91C100FD-SS

• Ethernet Connection Type: 10 Base-T, 100 Base-TX
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Product: Ethernet Controllers
• Number Of Transceivers: 1
• Standard Supported: 802.3
• Data Rate: 10 MB, 100 MB
• Supply Voltage (max): 7 V
• Supply Voltage (min): 0.3 V
• Supply Current (max): 40 mA
• Maximum Operating Temperature: + 70 C
• Package / Case: QFP-208
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

BYTE
BYTE
HIGH
LOW
COMMAND SET:
SMSC LAN91C100FD Rev. D
FEAST Fast Ethernet Controller with Full Duplex Capability
The three command bits determine the command issued as described below:
xyz
000
001
010
011
100
101
110
111
x
0)
1)
2)
3)
4)
5)
6)
7)
NOOP - NO OPERATION
ALLOCATE MEMORY FOR TX - N2,N1,N0 defines the amount of memory requested as
(value + 1) * 256 bytes. Namely N2,N1,N0 = 1 will request 2 * 256 = 512 bytes. A shift-based
divide by 256 of the packet length yields the appropriate value to be used as N2,N1,N0.
Immediately generates a completion code at the ALLOCATION RESULT REGISTER. Can
optionally generate an interrupt on successful completion. N2,N1,N0 are ignored by the
LAN91C100FD but should be implemented in LAN91C100FD software drivers for LAN9000
compatibility.
RESET MMU TO INITIAL STATE - Frees all memory allocations, clears relevant interrupts,
resets packet FIFO pointers.
REMOVE FRAME FROM TOP OF RX FIFO - To be issued after CPU has completed
processing of present receive frame. This command removes the receive packet number from
the RX FIFO and brings the next receive frame (if any) to the RX area (output of RX FIFO).
REMOVE AND RELEASE TOP OF RX FIFO - Like 3) but also releases all memory used by
the packet presently at the RX FIFO output. The MMU busy time after issuing REMOVE and
RELEASE command depends on the time when the busy bit is cleared. The time from issuing
REMOVE and RELEASE command on the last receive packet to the time when receive FIFO
is empty depends on RX INT bit turning low. An alternate approach can be checking the read
RX FIFO register.
RELEASE SPECIFIC PACKET - Frees all pages allocated to the packet specified in the
PACKET NUMBER REGISTER. Should not be used for frames pending transmission.
Typically used to remove transmitted frames, after reading their completion status. Can be
used following 3) to release receive packet memory in a more flexible way than 4).
ENQUEUE PACKET NUMBER INTO TX FIFO - This is the normal method of transmitting a
packet just loaded into RAM. The packet number to be enqueued is taken from the PACKET
NUMBER REGISTER.
RESET TX FIFOs - This command will reset both TX FIFOs: The TX FIFO holding the packet
numbers awaiting transmission and the TX Completion FIFO. This command provides a
mechanism for canceling packet transmissions, and reordering or bypassing the transmit
queue.
disabled. Unlike the RESET MMU command, the RESET TX FIFOs does not release any
memory.
COMMAND
y
The RESET TX FIFOs command should only be used when the transmitter is
z
DATASHEET
Page 31
0
0
N2
Revision 1.0 (09-22-08)
N1
N0/BUSY
0