MT47H128M16RT-25E:C Micron Technology Inc, MT47H128M16RT-25E:C Datasheet - Page 128

• Manufacturer Part Number: MT47H128M16RT-25E:C
• Description: DRAM Chip DDR2 SDRAM 2G-Bit 128Mx16 1.8V 84-Pin FBGA Tray
• Manufacturer: Micron Technology Inc
• Type: DDR2 SDRAMr
• Series: -r

Specifications of MT47H128M16RT-25E:C

• Package: 84FBGA
• Density: 2 Gb
• Address Bus Width: 17 Bit
• Operating Supply Voltage: 1.8 V
• Maximum Clock Rate: 800 MHz
• Maximum Random Access Time: 0.4 ns
• Operating Temperature: 0 to 70 °C
• Format - Memory: RAM
• Memory Type: DDR2 SDRAM
• Memory Size: 2G (128M x 16)
• Speed: 2.5ns
• Interface: Parallel
• Voltage - Supply: 1.7 V ~ 1.9 V
• Package / Case: 84-TFBGA
• Lead Free Status / RoHS Status: Compliant

ODT Timing
PDF: 09005aef824f87b6
2gbddr2.pdf – Rev. E 06/10 EN
Once a 12ns delay (
bled via the EMR LOAD MODE command, ODT can be accessed under two timing
categories. ODT will operate either in synchronous mode or asynchronous mode, de-
pending on the state of CKE. ODT can switch anytime except during self refresh mode
and a few clocks after being enabled via EMR, as shown in Figure 81 (page 129).
There are two timing categories for ODT—turn-on and turn-off. During active mode
(CKE HIGH) and fast-exit power-down mode (any row of any bank open, CKE LOW,
MR[12 = 0]),
in Figure 83 (page 130).
During slow-exit power-down mode (any row of any bank open, CKE LOW, MR[12] = 1)
and precharge power-down mode (all banks/rows precharged and idle, CKE LOW),
t
ODT turn-off timing, prior to entering any power-down mode, is determined by the pa-
rameter
signal satisfies
(MIN) is satisfied,
shows the example where
occur until state T3. When
ODT turn-on timing prior to entering any power-down mode is determined by the pa-
rameter
satisfies
satisfied,
the example where
until state T3. When
ODT turn-off timing after exiting any power-down mode is determined by the parame-
ter
satisfies
satisfied,
the example where
When
ODT turn-on timing after exiting either slow-exit power-down mode or precharge power-
down mode is determined by the parameter
(page 134). At state Ta1, the ODT HIGH signal satisfies
down mode at state T1. When
parameters apply. Figure 88 (page 134) also shows the example where
not satisfied because ODT HIGH occurs at state Ta0. When
t
AONPD and
AONPD timing parameters apply.
t
AXPD (MIN), as shown in Figure 87 (page 133). At state Ta1, the ODT LOW signal
t
AXPD (MIN) is not satisfied,
t
t
t
t
ANPD (MIN), as shown in Figure 85 (page 131). At state T2, the ODT HIGH
ANPD, as shown in Figure 86 (page 132). At state T2, the ODT HIGH signal
ANPD (MIN) prior to entering power-down mode at T5. When
AXPD (MIN) after exiting power-down mode at state T1. When
t
t
AOND and
AOFD and
t
AOND,
t
AOFPD timing parameters are applied, as shown in Figure 84 (page 131).
t
ANPD (MIN) prior to entering power-down mode at T5. When
t
AOFD and
t
t
t
MOD) has been satisfied, and after the ODT function has been ena-
ANPD (MIN) is not satisfied because ODT HIGH does not occur
AXPD (MIN) is not satisfied because ODT LOW occurs at state Ta0.
t
t
t
ANPD (MIN) is not satisfied,
AON,
t
AOF timing parameters apply. Figure 87 (page 133) also shows
AON timing parameters apply. Figure 86 (page 132) also shows
t
t
ANPD (MIN) is not satisfied,
ANPD (MIN) is not satisfied because ODT HIGH does not
t
AOFD, and
128
t
AOF timing parameters apply. Figure 85 (page 131) also
t
AXPD (MIN) is satisfied,
t
AOFPD timing parameters apply.
Micron Technology, Inc. reserves the right to change products or specifications without notice.
t
AOF timing parameters are applied, as shown
t
AXPD (MIN), as shown in Figure 88
2Gb: x4, x8, x16 DDR2 SDRAM
t
AONPD timing parameters apply.
t
t
AOFPD timing parameters apply.
AXPD (MIN) after exiting power-
t
AOND and
t
AXPD (MIN) is not satisfied,
© 2006 Micron Technology, Inc. All rights reserved.
t
AON timing
t
AXPD (MIN) is
t
ODT Timing
t
ANPD (MIN) is
AXPD (MIN) is
t
ANPD