MCIMX31LCVMN4D Freescale, MCIMX31LCVMN4D Datasheet - Page 50

• Manufacturer Part Number: MCIMX31LCVMN4D
• Manufacturer: Freescale

Specifications of MCIMX31LCVMN4D

• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Compliant

1
2
3
4
Electrical Characteristics
4.3.13
This section describes the electrical information of the I
4.3.13.1 I
Figure 41
supply is 2.7 V. 1
50
IC10
IC11
IC12
IC1
IC2
IC3
IC4
IC5
IC6
IC7
IC8
IC9
A device must internally provide a hold time of at least 300 ns for I2DAT signal in order to bridge the undefined region of the
falling edge of I2CLK.
The maximum hold time has to be met only if the device does not stretch the LOW period (ID IC6) of the I2CLK signal.
A Fast-mode I
250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the I2CLK signal.
If such a device does stretch the LOW period of the I2CLK signal, it must output the next data bit to the I2DAT line max_rise_time
(ID No IC10) + data_setup_time (ID No IC8) = 1000 + 250 = 1250 ns (according to the Standard-mode I
before the I2CLK line is released.
C
ID
I2CLK
b
I2DAT
= total capacitance of one bus line in pF.
I2CLK cycle time
Set-up time for STOP condition
HIGH Period of I2CLK Clock
LOW Period of the I2CLK Clock
Data set-up time
Bus free time between a STOP and START condition
Rise time of both I2DAT and I2CLK signals
Fall time of both I2DAT and I2CLK signals
Capacitive load for each bus line (C
Hold time (repeated) START condition
Data hold time
Set-up time for a repeated START condition
depicts the timing of I
I
2
IC2
2
C Electrical Specifications
2
START
C-bus device can be used in a standard-mode I
C Module Timing
Table 40. I
IC10
IC6
Parameter
IC8
2
C Module Timing Parameters—I
IC1
MCIMX31C/MCIMX31LC Technical Data, Rev. 4.3
2
IC10
C module.
Figure 41. I
IC5
b
)
IC4
Table 40
2
IC11
C Bus Timing Diagram
IC11
lists the I
2
C-bus system, but the requirement of set-up time (ID IC7) of
2
C Module.
IC7
Standard Mode
Min
250
2
4.0
4.0
4.0
4.7
4.7
4.7
10
2
0
—
—
—
START
C module timing parameters where the I/O
C Pin I/O Supply=2.7 V
1
3.45
1000
Max
300
400
—
—
—
—
—
—
—
—
2
20+0.1C
20+0.1C
IC3
100
Min
2.5
0.6
0.6
0.6
1.3
0.6
1.3
0
—
STOP
Fast Mode
1
3
Freescale Semiconductor
b
b
4
4
2
C-bus specification)
IC9
Max
0.9
300
300
400
—
—
—
—
—
—
—
—
START
2
Unit
pF
μs
μs
μs
μs
μs
μs
μs
ns
μs
ns
ns