5962-8867809RX Cypress Semiconductor Corp, 5962-8867809RX Datasheet
5962-8867809RX
Specifications of 5962-8867809RX
Related parts for 5962-8867809RX
5962-8867809RX Summary of contents
Page 1
... D. A. DiCenzo MICROCIRCUIT, MEMORY, DIGITAL, Michael A. Frye CMOS, UV ERASABLE, PROGRAMMABLE LOGIC ARRAY, MONOLITHIC SILICON 88-09-26 SIZE B A SHEET DATE (YR-MO-DA) 89-12- Frye 05-11-15 Raymond Monnin DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http://www.dscc.dla.mil CAGE CODE 5962-88678 67268 5962-E047-06 APPROVED B 12 ...
Page 2
... SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN shall be as shown in the following example: 5962- 88678 Drawing number Device type (see 1.2.1) 1 ...
Page 3
... Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are described in table I. STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 http://assist.daps.dla.mil/quicksearch/ SIZE A REVISION LEVEL B or http://assist.daps.dla.mil 5962-88678 SHEET 3 ...
Page 4
... REVISION LEVEL SHEET B │ │ Unit │ │ │ │ V │ │ │ │ │ │ │ V │ ...
Page 5
... MHz │ │ 22 │ │ │ 28.5 │ (ac) = (0.6 mA/MHz) X (operating CC 5962-88678 REVISION LEVEL SHEET B 5 ...
Page 6
... Device types Case outlines STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 01, 05, 09 02, 06 Terminal Terminal symbol number FIGURE 1. Terminal connections. SIZE A 03, 07, 11 04, 08 I I/O I 5962-88678 REVISION LEVEL SHEET B 6 ...
Page 7
... Device types 02, 06, and 10 Truth table Device types 03, 07, and 11 Truth table I Device types 04, 08, and 12 Truth table I/O I FIGURE 2. Truth table (unprogrammed). SIZE A Output pins I/O I/O I/O I/O I Output pins Output pins I Output pins I/O I 5962-88678 REVISION LEVEL SHEET ...
Page 8
... STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 FIGURE 3. Output load circuit. SIZE A REVISION LEVEL 5962-88678 SHEET B 8 ...
Page 9
... STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 DSCC FORM 2234 APR 97 FIGURE 4. Switching waveforms. SIZE A REVISION LEVEL 5962-88678 SHEET B 9 ...
Page 10
... In addition, the manufacturer's PIN may also be marked. For packages where the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “ ...
Page 11
... V at +25°C using loose timing (i.e., +5.75 V and V +4. +25°C using loose timing +5 +25°C. m measurement) shall be measured only for the initial test and after process or design SIZE µs). ACC 2 (1 week at 12,000 µW/ Exposure of the 5962-88678 REVISION LEVEL SHEET B 11 ...
Page 12
... SMD. DSCC will maintain a record of users and this list will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. 6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone (614) 692-0547 ...
Page 13
... STANDARD MICROCIRCUIT DRAWING BULLETIN Approved sources of supply for SMD 5962-88678 are listed below for immediate acquisition information only and shall be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of compliance has been submitted to and accepted by DSCC-VA ...
Page 14
... Standardized military drawing PIN 1/ 5962-8867812RA 5962-8867812SA 5962-8867812XA 1/ The lead finish shown for each PIN representing a hermetic package is the most readily available from the manufacturer listed for that part. If the desired lead finish is not listed, contact the vendor to determine its availability. 2/ Caution. Do not use this number for item acquisition. Items acquired to this number may not satisfy the performance requirements of this drawing ...