5962-8867809RX Cypress Semiconductor Corp, 5962-8867809RX Datasheet - Page 10

• Manufacturer Part Number: 5962-8867809RX
• Manufacturer: Cypress Semiconductor Corp

Specifications of 5962-8867809RX

• Lead Free Status / RoHS Status: Not Compliant

DSCC FORM 2234
APR 97
in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where the entire SMD PIN number is not
feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification
mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used.
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-38535,
appendix A and the requirements herein.
with each lot of microcircuits delivered to this drawing.
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
a wide variety of configurations; two processing options are provided for selection in the contract, using an altered item
drawing.
and table II. It is recommended that users perform subgroups 7 and 9 after programming to verify the specific program
configuration.
herein, including the requirements of the altered item drawing, shall be satisfied by the manufacturer prior to delivery.
prior to quality conformance inspection. The following additional criteria shall apply:
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing.
3.9 Verification and review. DSCC, DSCC's agent and the acquiring activity retain the option to review the manufacturer's
3.10 Processing options. Since the device is capable of being programmed by either the manufacturer or the user to result in
3.10.1 Unprogrammed device delivered to the user. All testing shall be verified through group A testing as defined in 3.2.2.1
3.10.2 Manufacturer-programmed device delivered to the user. All testing requirements and quality assurance provisions
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in
DEFENSE SUPPLY CENTER COLUMBUS
a. Burn-in test (method 1015 of MIL-STD-883).
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
c. A data retention stress test shall be included as part of the screening procedure and shall consist of the following
(1)
(2)
tests prior to burn-in are optional at the discretion of the manufacturer.
steps:
COLUMBUS, OHIO 43218-3990
MICROCIRCUIT DRAWING
Margin test method A. Steps 1 through 3 may be performed at wafer level.
(1)
Test condition C or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or procuring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified
in method 1015 of MIL-STD-883.
T
A
= +125°C, minimum.
Program greater than 95 percent of the total number of cells, including the slowest programming cell. The
remaining cells shall provide a worst case speed pattern.
STANDARD
SIZE
A
REVISION LEVEL
B
SHEET
5962-88678
10