AD73322LYRUZ Analog Devices Inc, AD73322LYRUZ Datasheet - Page 22

• Manufacturer Part Number: AD73322LYRUZ
• Manufacturer: Analog Devices Inc

Specifications of AD73322LYRUZ

• Single Supply Voltage (typ): 3V
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 3.3V
• Package Type: TSSOP
• Lead Free Status / RoHS Status: Compliant

AD73322L
In a single AD73322L configuration, each 16-bit data frame
sent from the DSP to the device is interpreted as DAC data, but
it is necessary to send two DAC words per sample period in
order to ensure DAC update. Also, as the device count setting
defaults to 1, it must be set to 2 (001b) to ensure correct update
of both DACs on the AD73322L.
Appendix B details the initialization and operation of an
AD73322L in normal Data Mode.
Mixed Program/Data Mode
This mode allows the user to send control words to the device
along with the DAC data. This permits adaptive control of the
device whereby control of the input/output gains etc., can be
affected by interleaving control words along with the normal
flow of DAC data. The standard data frame remains 16 bits,
but now the MSB is used as a flag bit to indicate whether the
remaining 15 bits of the frame represent DAC data or control
information. In the case of DAC data, the 15 bits are loaded
with MSB justification and LSB set to 0 to the DAC register.
Mixed mode is enabled by setting the MM bit (CRA:1) to 1 and
the DATA/PGM bit (CRA:0) to 1. In the case where control
setting changes will be required during normal operation, this
mode allows the ability to load both control and data informa-
tion with the slight inconvenience of formatting the data. Note
that the output samples from the ADC will also have the MSB
set to zero to indicate it is a data word.
Appendix C details the initialization and operation of an
AD73322L operating in mixed mode. Note that it is not essen-
tial to load the control registers in Program Mode before setting
mixed mode active. It is also possible to initiate mixed mode by
programming CRA with the first control word and then inter-
leaving control words with DAC data.
SDOFS
SDIFS
SCLK
SDO
SDI
SE
ADC SAMPLE WORD (DEVICE 2)
DAC DATA WORD (DEVICE 2)
ADC SAMPLE WORD (DEVICE 1)
DAC DATA WORD (DEVICE 1)
Digital Loop-Back
This mode can be used for diagnostic purposes and allows the
user to feed the ADC samples from the ADC register directly to
the DAC register. This forms a loop-back of the analog input to
the analog output by reconstructing the encoded signal using
the decoder channel. The serial interface will continue to work,
which allows the user to control gain settings, etc. Only when
DLB is enabled with mixed mode operation can the user disable
the DLB, otherwise the device must be reset.
SPORT Loop-Back
This mode allows the user to verify the DSP interfacing and
connection by writing words to the SPORT of the devices and
have them returned back unchanged after a delay of 16 SCLK
cycles. The frame sync and data word that are sent to the device
are returned via the output port. Again, SLB mode can only be
disabled when used in conjunction with mixed mode, otherwise
the device must be reset.
Analog Loop-Back
In Analog Loop-Back mode, the differential DAC output is
connected, via a loop-back switch, to the ADC input (see Figure
13). This mode allows the ADC channel to check functionality
of the DAC channel as the reconstructed output signal can be
monitored using the ADC as a sampler. Analog Loop-Back is
enabled by setting the ALB bit (CRF:7).
NOTE: Analog Loop-Back can only be enabled if the Analog
Gain Tap is powered down (CRC:1 = 0).
REFOUT
REFCAP
VOUTP1
VOUTN1
VFBN1
VFBP1
VINN1
VINP1
INVERTING
OP AMPS
V
REF
LOOP-BACK
ANALOG
SELECT
+6/–15dB
PGA
REFERENCE
GAIN
CONTINUOUS
LOW-PASS
1
FILTER
TIME
INVERT
TAP POWERED
ANALOG GAIN
V
AD73322L
REF
DOWN
0/38dB
SINGLE-
ENABLE
ENDED
PGA