AD7731BNZ Analog Devices Inc, AD7731BNZ Datasheet - Page 21

• Manufacturer Part Number: AD7731BNZ
• Description: IC ADC 24BIT SIGMA-DELTA 24DIP
• Manufacturer: Analog Devices Inc

Specifications of AD7731BNZ

• Data Interface: DSP, Serial, SPI™
• Number Of Bits: 24
• Sampling Rate (per Second): 6.4k
• Number Of Converters: 1
• Power Dissipation (max): 125mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Package / Case: 24-DIP (0.300", 7.62mm)
• Resolution (bits): 24bit
• Sampling Rate: 6.4kSPS
• Input Channel Type: Single Ended
• Supply Voltage Range - Analog: 4.75V To 5.25V
• Supply Voltage Range - Digital: 2.7V To 5.25V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7731EBZ - BOARD EVALUATION FOR AD7731
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

CALIBRATION OPERATION SUMMARY
The AD7731 contains a number of calibration options as outlined previously. Table XVI summarizes the calibration types, the op-
erations involved and the duration of the operations. There are two methods of determining the end of calibration. The first is to
monitor the hardware RDY pin using either interrupt-driven or polling routines. The second method is to do a software poll of the
RDY bit in the Status Register. This can be achieved by setting up the part for continuous reads of the Status Register once a calibra-
tion has been initiated. The RDY pin and RDY bit go high on initiating a calibration and return low at the end of the calibration
routine. At this time, the MD2, MD1, MD0 bits of the Mode Register have returned to 0, 0, 0. The FAST and SKIP bits are treated
as 0 for the calibration sequence so the full filter is always used for the calibration routines. See Calibration section for full details.
Calibration Type
Internal Zero-Scale
Internal Full-Scale
System Zero-Scale
System Full-Scale
REV. A
REV. 0
MD2, MD1, Duration to RDY Duration to RDY
MD0
1, 0, 0
1, 0, 1
1, 1, 0
1, 1, 1
Low (CHP = 1)
22
44
22
22
1/Output Rate 24
1/Output Rate 48
1/Output Rate 24
1/Output Rate 24
Table XVI. Calibration Operations
Low (CHP = 0)
–21–
1/Output Rate Calibration on internal shorted input with PGA set
1/Output Rate Calibration on internally-generated input full-scale
1/Output Rate Calibration on externally-applied input voltage with
1/Output Rate Calibration on externally-applied input voltage with
Calibration Sequence
for selected input range. The Offset Calibration
Register for the selected channel is updated at the
end of this calibration sequence. For full self-cali-
bration, this calibration should be preceded by an
Internal Full-Scale calibration. For applications
which require an Internal Zero-Scale and System
Full Scale calibration, this Internal Zero-Scale
calibration should be performed first.
with PGA set for selected input range. The Gain
Calibration Register for the selected channel is
updated at the end of this calibration sequence. It is
recommended that internal full-scale calibrations
are performed on the operating input range except
for the 20 mV and 40 mV input ranges where opti-
mum results are achieved by calibrating on the
80 mV range. This calibration should be followed
by either an Internal Zero-Scale or System Zero-
Scale calibration. This calibration should be fol-
lowed by either an Internal Zero-Scale or System
Zero-Scale calibration. This zero-scale calibration
should be performed at the operating input range.
PGA set for selected input range. The input applied
is assumed to be the zero-scale of the system. For
full system calibration, this System Zero-Scale
calibration should be performed first. For applica-
tions which require a System Zero-Scale and Inter-
nal Full Scale calibration, this calibration should be
preceded by the Internal Full-Scale calibration. The
Offset Calibration Register for the selected channel
is updated at the end of this calibration sequence.
PGA set for selected input range. The input applied
is assumed to be the full-scale of the system. This
calibration should be preceded by a System Zero-
Scale or Internal Zero-Scale calibration. The Gain
Calibration Register for the selected channel is
updated at the end of this calibration sequence.
AD7731