X9418WV24Z-2.7 Intersil, X9418WV24Z-2.7 Datasheet - Page 2

• Manufacturer Part Number: X9418WV24Z-2.7
• Description: IC XDCP DUAL 64TAP 10K 24-TSSOP
• Manufacturer: Intersil
• Series: XDCP™r

Specifications of X9418WV24Z-2.7

• Taps: 64
• Resistance (ohms): 10K
• Number Of Circuits: 2
• Temperature Coefficient: 300 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 24-TSSOP
• Resistance In Ohms: 10K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Ordering Information
*Add "T1" suffix for tape and reel.
NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin
plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are
MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
PIN DESCRIPTIONS
Host Interface Pins
Serial Clock (SCL)
The SCL input is used to clock data into and out of the
X9418.
Serial Data (SDA)
SDA is a bidirectional pin used to transfer data into
and out of the device. It is an open drain output and
may be wire-ORed with any number of open drain or
open collector outputs. An open drain output requires
the use of a pull-up resistor. For selecting typical
values, refer to the guidelines for calculating typical
values on the bus pull-up resistors graph.
Device Address (A
The Address inputs are used to set the least
significant 4 bits of the 8-bit slave address. A match in
the slave address serial data stream must be made
with
communication with the X9418. A maximum of 16
devices may occupy the 2-wire serial bus.
X9418WV24*
X9418WV24Z* (Note)
X9418WP24I-2.7
X9418WS24I-2.7
X9418WS24IZ-2.7 (Note) X9418WS ZG
X9418WV24-2.7*
X9418WV24Z-2.7* (Note) X9418WV ZF
X9418WV24I-2.7
X9418WV24IZ-2.7 (Note) X9418WV ZG
X9418YS24-2.7
X9418YS24Z-2.7 (Note)
X9418YS24I-2.7
X9418YS24IZ-2.7 (Note)
X9418YV24I-2.7*
X9418YV24IZ-2.7* (Note) X9418YV ZG
PART NUMBER
the
Address
0
- A
PART MARKING
X9418WV
X9418WV Z
X9418WP G
X9418WS G
X9418WV F
X9418WV G
X9418YS F
X9418YS ZF
X9418YS G
X9418YS ZG
X9418YV G
input
3
)
2
in
order
V
CC
2.7 to 5.5
5 ±10%
(V)
LIMITS
to
initiate
ORGANIZATION
POTENTIOMET
X9418
(kΩ)
ER
2.5
10
10
Potentiometer Pins
V
The V
terminal connections on either end of a mechanical
potentiometer.
V
The wiper outputs are equivalent to the wiper output of
a mechanical potentiometer.
Hardware Write Protect Input (WP)
The WP pin when low prevents nonvolatile writes to
the Data Registers.
Analog Supplies V+, V-
The Analog Supplies V+, V- are the supply voltages
for the XDCP analog section.
H
W
TEMPERATU
/R
/R
RE RANGE
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
H
0 to +70
0 to +70
0 to +70
0 to +70
0 to +70
0 to +70
W
H
(°C)
(V
/R
(V
H0
H
W0
/R
and V
/R
H0
24 Ld TSSOP (4.4MM)
24 Ld TSSOP (4.4MM) (Pb-free) MDP0044
24 Ld PDIP
24 Ld SOIC (300MIL)
24 Ld SOIC (300MIL) (Pb-free)
24 Ld TSSOP (4.4MM)
24 Ld TSSOP (4.4MM) (Pb-free) MDP0044
24 Ld TSSOP (4.4MM)
24 Ld TSSOP (4.4MM) (Pb-free) MDP0044
24 Ld SOIC (300MIL)
24 Ld SOIC (300MIL) (Pb-free)
24 Ld SOIC (300MIL)
24 Ld SOIC (300MIL) (Pb-free)
24 Ld TSSOP (4.4MM)
24 Ld TSSOP (4.4MM) (Pb-free) MDP0044
W0
- V
H1
L
- V
/R
/R
W1
L
PACKAGE
H1
inputs are equivalent to the
/R
), V
W1
L
)
/R
L
(V
L0
/R
L0
PKG. DWG. #
MDP0044
E24.6
M24.3
M24.3
MDP0044
MDP0044
M24.3
M24.3
M24.3
M24.3
MDP0044
October 12, 2006
- V
L1
FN8194.3
/R
L1
)