CY7C374I-100JC Cypress Semiconductor Corp, CY7C374I-100JC Datasheet - Page 5

• Manufacturer Part Number: CY7C374I-100JC
• Description: IC CPLD 128 MACROCELL 84-PLCC
• Manufacturer: Cypress Semiconductor Corp
• Series: Ultralogic™r

Specifications of CY7C374I-100JC

• Memory Type: FLASH
• Programmable Type: In-System Reprogrammable™ (ISR™) Flash
• Delay Time Tpd(1) Max: 12.0ns
• Voltage Supply - Internal: 4.75 V ~ 5.25 V
• Number Of Logic Elements/blocks: 8
• Number Of Macrocells: 128
• Number Of I /o: 64
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 84-PLCC
• Voltage: 3.3V/5V
• Family Name: FLASH370i
• # Macrocells: 128
• Number Of Usable Gates: 3200
• Propagation Delay Time: 12ns
• Number Of Logic Blocks/elements: 8
• # I/os (max): 64
• Operating Supply Voltage (typ): 5V
• In System Programmable: Yes
• Operating Supply Voltage (min): 4.75V
• Operating Supply Voltage (max): 5.25V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 84
• Package Type: PLCC
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Features: -
• Number Of Logic Elements/cells: -
• Lead Free Status / RoHS Status: Not Compliant, Contains lead / RoHS non-compliant
• Other names: 428-1270

Maximum Ratings
(Above which the useful life may be impaired. For user guide-
lines, not tested.)
Storage Temperature ................................. –65 C to +150 C
Ambient Temperature with
Power Applied............................................. –55 C to +125 C
Supply Voltage to Ground Potential ............... –0.5V to +7.0V
DC Voltage Applied to Outputs
in High Z State ............................................... –0.5V to +7.0V
DC Input Voltage............................................ –0.5V to +7.0V
DC Program Voltage .....................................................12.5V
Output Current into Outputs.........................................16 mA
Electrical Characteristics
Notes:
Document #: 38-03031 Rev. **
10. Measured with 16-bit counter programmed into each logic block.
2.
3.
4.
5.
6.
7.
8.
9.
Parameter
V
V
V
V
V
I
I
I
I
I
I
I
I
IX
OZ
OS
CC
BHL
BHH
BHLO
BHHO
OH
OHZ
OL
IH
IL
T
See the last page of this specification for Group A subgroup testing information.
If V
I
When the I/O is three-stated, the bus-hold circuit can weakly pull the I/O to a maximum of 4.0V if no leakage current is allowed. This voltage is lowered significantly
by a small leakage current. Note that all I/Os are three-stated during ISR programming. Refer to the application note “Understanding Bus Hold” for additional
information.
These are absolute values with respect to device ground. All overshoots due to system or tester noise are included.
Not more than one output should be tested at a time. Duration of the short circuit should not exceed 1 second. V
problems caused by tester ground degradation.
Tested initially and after any design or process changes that may affect these parameters.
OH
A
is the “instant on” case temperature.
CCIO
= –2 mA, I
is not specified, the device can be operating in either 3.3V or 5V I/O mode; V
Output HIGH Voltage
Output HIGH Voltage
with Output Disabled
Output LOW Voltage
Input HIGH Voltage
Input LOW Voltage
Input Load Current
Output Leakage Current
Output Short
Circuit Current
Power Supply Current
Input Bus Hold LOW
Sustaining Current
Input Bus Hold HIGH
Sustaining Current
Input Bus Hold LOW
Overdrive Current
Input Bus Hold HIGH
Overdrive Current
OL
= 2 mA for SDO.
Description
[8, 9]
Over the Operating Range
[9]
V
V
V
Guaranteed Input Logical HIGH voltage for all inputs
Guaranteed Input Logical LOW voltage for all inputs
V
V
V
V
V
f = 1 MHz, V
V
V
V
V
CC
CC
CC
I
CC
CC
CC
CC
CC
CC
CC
CC
= Internal GND, V
= Max., V
= Min.
= Max.
= Min.
= Max., V
= Max., V
= Max., I
= Min., V
= Min., V
= Max.
= Max.
IN
OUT
IL
IH
I
I
I
I
I
I
O
O
OUT
OH
OH
OH
OH
OL
OL
= GND, V
= 0.8V
= GND or V
= 2.0V
= 3.3V, Output Disabled
= 16 mA (Com’l/Ind)
= 12 mA (Mil)
= 0 mA,
Test Conditions
= –3.2 mA (Com’l/Ind)
= –2.0 mA (Mil)
= 0 A (Com’l/Ind)
= –50 A (Com’l/Ind)
= 0.5V
[3, 4]
I
= V
Static Discharge Voltage ........................................... >2001V
(per MIL-STD-883, Method 3015)
Latch-Up Current..................................................... >200 mA
Operating Range
CC
CC
Commercial
Industrial
Military
[10]
O
Range
CC
= V
=V
[2]
CC
CCINT
, Output Disabled
[5, 6]
Com’l/Ind.
Com’l “L” –66
Military
.
[5]
[5, 6]
[5]
[6]
–55°C to +125°C
Temperature
0 C to +70 C
40 C to +85 C
Ambient
OUT
[7]
[7]
= 0.5V has been chosen to avoid test
Min.
–0.5
+75
–10
–50
–30
–75
2.4
2.0
0
5V
5V
V
0.25V
5V
V
CCINT
Typ.
–70
125
125
75
CC
0.5V
0.5V
CY7C374i
Max.
–125
–160
+500
–500
+10
+50
200
125
250
4.0
3.6
0.5
7.0
0.8
Page 5 of 15
3.3V
3.3V
5V
5V
V
OR
OR
CCIO
0.25V
0.5V
Unit
mA
mA
mA
mA
0.3V
0.3V
V
V
V
V
V
V
V
V
A
A
A
A
A
A
A