DS18S20 Maxim Integrated Products, DS18S20 Datasheet - Page 2

• Manufacturer Part Number: DS18S20
• Description: Board Mount Temperature Sensors
• Manufacturer: Maxim Integrated Products

Specifications of DS18S20

• Full Temp Accuracy: +/- 2 C
• Package / Case: TO-92
• Digital Output - Bus Interface: Serial (1-Wire)
• Digital Output - Number Of Bits: 9 bit
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 55 C
• Output Type: Digital
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

ORDERING INFORMATION
DS18B20
DS18B20+
DS18B20/T&R
DS18B20+T&R
DS18B20-SL/T&R
DS18B20-SL+T&R
DS18B20U
DS18B20U+
DS18B20U/T&R
DS18B20U+T&R
DS18B20Z
DS18B20Z+
DS18B20Z/T&R
DS18B20Z+T&R
+Denotes a lead-free package. A “+” will appear on the top mark of lead-free packages.
T&R = Tape and reel.
*TO-92 packages in tape and reel can be ordered with straight or formed leads. Choose “SL” for straight leads. Bulk TO-92 orders are straight
leads only.
PIN DESCRIPTION
OVERVIEW
Figure 1 shows a block diagram of the DS18B20, and pin descriptions are given in the Pin Description
table. The 64-bit ROM stores the device’s unique serial code. The scratchpad memory contains the 2-byte
temperature register that stores the digital output from the temperature sensor. In addition, the scratchpad
provides access to the 1-byte upper and lower alarm trigger registers (T
configuration register. The configuration register allows the user to set the resolution of the temperature-
to-digital conversion to 9, 10, 11, or 12 bits. The T
(EEPROM), so they will retain data when the device is powered down.
The DS18B20 uses Maxim’s exclusive 1-Wire bus protocol that implements bus communication using
one control signal. The control line requires a weak pullup resistor since all devices are linked to the bus
via a 3-state or open-drain port (the DQ pin in the case of the DS18B20). In this bus system, the
microprocessor (the master device) identifies and addresses devices on the bus using each device’s unique
64-bit code. Because each device has a unique code, the number of devices that can be addressed on one
1, 2, 6,
7, 8
SO
3
4
5
PART
2, 3, 5,
µSOP
PIN
6, 7
8
1
4
TO-92
—
3
2
1
TEMP RANGE
-55°C to +125°C
-55°C to +125°C
-55°C to +125°C
-55°C to +125°C
-55°C to +125°C
-55°C to +125°C
-55°C to +125°C
-55°C to +125°C
-55°C to +125°C
-55°C to +125°C
-55°C to +125°C
-55°C to +125°C
-55°C to +125°C
-55°C to +125°C
NAME
GND
N.C.
V
DQ
DD
No Connection
Optional V
parasite power mode.
Data Input/Output. Open-drain 1-Wire interface pin. Also
provides power to the device when used in parasite power
mode (see the Powering the DS18B20 section.)
Ground
2 of 22
PIN-PACKAGE
3 TO-92
3 TO-92
3 TO-92 (2000 Piece)
3 TO-92 (2000 Piece)
3 TO-92 (2000 Piece)*
3 TO-92 (2000 Piece)*
8 µSOP
8 µSOP
8 µSOP (3000 Piece)
8 µSOP (3000 Piece)
8 SO
8 SO
8 SO (2500 Piece)
8 SO (2500 Piece)
H
DD
, T
. V
L
, and configuration registers are nonvolatile
DD
must be grounded for operation in
FUNCTION
H
and T
TOP MARK
L
DS18B20
DS18B20
DS18B20
DS18B20
) and the 1-byte
18B20
18B20
18B20
18B20
18B20
18B20
18B20
18B20
18B20
18B20
DS18B20