TX09D70VM1CBA HITACHI, TX09D70VM1CBA Datasheet
TX09D70VM1CBA
Specifications of TX09D70VM1CBA
Available stocks
Related parts for TX09D70VM1CBA
TX09D70VM1CBA Summary of contents
Page 1
... FOR MESSRS : CUSTOMER’S ACCEPTANCE SPECIFICATIONS No. ITEM 1 COVER 2 RECORD OF REVISION 3 GENERAL DATA 4 ABSOLUTE MAXIMUM RATINGS 7B64PS 2704-TX09D70VM1CBA-6 5 ELECTRICAL CHARACTERISTICS 7B64PS 2705-TX09D70VM1CBA-6 6 OPTICAL CHARACTERISTICS 7 BLOCK DIAGRAM 8 INTERFACE TIMING CHART 9 OUTLINE DIMENSIONS 10 APPEARANCE STANDARD 11 PRECAUTION IN DESIGN 12 DESIGNATION OF LOT MARK 13 PRECAUTION FOR USE ACCEPTED BY： ...
Page 2
... INTERFACE TIMING Revised Horizontal Timing Sequence of CL1 and CL2. 8.2 POWER ON/OFF SEQUENCE Deleted PCI setting and Note. 8.5 POWER SUPPLY CIRCUIT FOR LED BL Added Power Supply Circuit for LED BL Sh. 7B64PS 2701-TX09D70VM1CBA-6 No. STORAGE Max. Min. Max. (70℃) (-30℃) (80℃) ↓ ...
Page 3
... Ambient Temperature Ta( ) Note 5 : IFP Conditions : pulse width≦10ms and Duty≦1/10 a=25 T ℃ 200 100 100 Duty Ratio(%) Sh. 7B64PS 2701-TX09D70VM1CBA-6 No. TYP. TYP. 430 (400) 65 (70) → 65 (70) 80 (80) 40 (60) SYMBOL MAX SYMBOL MAX 100 → 8.5mA ( 8.5 ...
Page 4
... OPTICAL CHARACTERISTICS OF LCD Revised Brightness and Color Tone of SPEC 12.2 Location of lot mark Lot mark change: Print on FPC → Barcode label 9.OUTLINE DIMENSIONS The connector on FPC changed. Added 12.2 REVISION (REV.) CONTROL REV No Connector Changed Sh. 7B64PS 2701-TX09D70VM1CBA-6 No. TYP. IF=20mA - 3. ↓ TYP. IF=20mA - 3 ...
Page 5
... R,G,B Vertical Stripe Transmissive Color TFT LCD (Normally White) Active Matrix K 262 Colors (R,G,B 6 Bit Digital each) Light Emitting Diode (LED 36g 50 pin C-MOS 6 O’clock (The direction it’s hard to be discolored) Sh. 7B64PS 2703-TX09D70VM1CBA-6 No. (Except FPC Area) PAGE 3-1/1 ...
Page 6
...
Page 7
... DATE Jan.18,’11 ELECTRONICS CO.,LTD. OPERATING STORAGE Min. Max. Min. -20℃ 70℃ -30℃ (Note 1) (Note 1) 2 2.45m (0.25G) 2 29.4m (3G) Not Acceptable Not Acceptable Sh. 7B64PS 2704-TX09D70VM1CBA-6 No. REMARKS Max. 80℃ (Note 2,3,6,7,9,10) Without condensation 2 11.76m/s (Note 4,5) (1.2G) 2 490m/s (Note 5,8) (50G) PAGE 4-2/2 ...
Page 8
... AVDD - VGH - Gate VGL - IDD 16 Vertical IAVDD Gray scale IGH IGL fFLM - MIN. TYP. IF=20mA - 3 VR= Sh. 7B64PS 2705-TX09D70VM1CBA-6 No. Ta=25℃ MIN. TYP. MAX. 2.3 3.3 3.6 7.5 8.48 9.5 13.0 15.0 17.0 -8.0 -5.0 -2.0 - 0.56 2.0 - 2.3 4.0 - 0.033 0. ...
Page 9
... K =0° θ=0° tr+ =0° θ=0° (Measurement condition : HITACHI standard) Note (4)~(7) : See page 6-2/2 Note 3 : Definition of the brightness uniformity ( X=190 Y=70 9 Y=160 6 Y=250 3 Sh. 7B64PS 2706-TX09D70VM1CBA-6 No. Ta=25℃ MIN. TYP. MAX. UNIT - (400 (70 (70) - deg - (80 (60) - ...
Page 10
...
Page 11
...
Page 12
...
Page 13
... Note : Vertical Total should be set to odd. Sh. 7B64PS 2708-TX09D70VM1CBA-6 No. UNIT SYMBOL Line T0 Line T1 Line T2 Line T3 Line T4 Line T5 Pixel Clock T6 Pixel Clock T7 Pixel Clock T8 Pixel Clock T9 Pixel Clock T10 Pixel Clock ...
Page 14
...
Page 15
...
Page 16
...
Page 17
...
Page 18
... Red : : Red(2) 1 Red(1) 1 Red(0) 1 Black 0 Green(62) 0 Green(61 Green : : Green(2) 0 Green(1) 0 Green(0) 0 Black 0 Blue(62) 0 Blue(61 Blue : : Blue(2) 0 Blue(1) 0 Blue(0) 0 KAOHSIUNG HITACHI DATE Jan.18,’11 ELECTRONICS CO.,LTD. Red Data Green Data LSB MSB Sh. 7B64PS 2708-TX09D70VM1CBA-6 No. Blue Data LSB MSB PAGE 8-6/10 LSB ...
Page 19
...
Page 20
...
Page 21
...
Page 22
... Anode Blue Data 46 47 Blue Data 48 Blue Data 49 Blue Data 50 Blue Data Sh. 7B64PS 2708-TX09D70VM1CBA-6 No. FUNCTION B5 Blue Data POL Data Polarity Judge pulse(Note2 Modulation Clock LOAD Source Driver Latch Pulse (CL1) CL2 Source Driver Shift Clock V0 Gray Scale Voltage V4 No Conncetion (Note3.) ...
Page 23
...
Page 24
... Viewing angle≦25° eye LCD Bezel 10.2 DEFINITION OF ZONE KAOHSIUNG HITACHI DATE Jan.18,’11 ELECTRONICS CO.,LTD. 25° 25° Active area (pixel area) Until 1mm outside around Active area A zone B zone C zone Sh. 7B64PS 2710- TX09D70VM1CBA-6 No. eye Metal bezel area (include I/F connector) PAGE 10-1/3 ...
Page 25
... The total number Those wiped out easily are acceptable To be judged by HITACHI STANDARD Same as above Sparkle mode 2 dots Black mode 2 dots Sparkle mode 2 dots & Black mode Sh. 7B64PS 2710- TX09D70VM1CBA-6 No. Maximum number acceptable ignored 4 none Maximum number acceptable 2 none Maximum number ...
Page 26
... Counting definition of adjacent dots(1 sets) : same as 1 dot defect. (g) Those wiped out easily are acceptable KAOHSIUNG HITACHI DATE Jan.18,’11 ELECTRONICS CO.,LTD. a dots defect included defect dot “X” is defined as follows. Adjacent dots to defect dot “X” : Sh. 7B64PS 2710- TX09D70VM1CBA-6 No. PAGE 10-3/3 ...
Page 27
... Maximum pressure to the surface must be less than 1.96×10 And if the pressure area is less than 1cm 1.96N. (8) Since the metal width is narrow on these locations (see page 9-1/1), please careful with handling. KAOHSIUNG HITACHI DATE Jan.18,’11 ELECTRONICS CO.,LTD maximum pressure must be less than Sh. 7B64PS 2711- TX09D70VM1CBA-6 No. 4 Pa. PAGE 11-1/2 ...
Page 28
... Keep the temperature between -30℃ and 80℃ at normal humidity. (3) Store the LCD modules in the container which is used for shipping from us. (4) No articles shall be left on the surface over an extended period of time. KAOHSIUNG HITACHI DATE Jan.18,’11 ELECTRONICS CO.,LTD. Sh. 7B64PS 2711- TX09D70VM1CBA-6 No. PAGE 11-2/2 ...
Page 29
...
Page 30
... The precaution that should be observed when handling LCM have been explained above. If any points are unclear or if you have any requests , please contact with HITACHI. KAOHSIUNG HITACHI DATE Jan.18,’11 ELECTRONICS CO.,LTD. Sh. 7B64PS 2713- TX09D70VM1CBA-6 No. PAGE 13-1/1 ...