TE28F160B3TA110 Intel, TE28F160B3TA110 Datasheet - Page 56

• Manufacturer Part Number: TE28F160B3TA110
• Manufacturer: Intel

Specifications of TE28F160B3TA110

• Cell Type: NOR
• Density: 16Mb
• Access Time (max): 110ns
• Interface Type: Parallel
• Boot Type: Top
• Address Bus: 20b
• Operating Supply Voltage (typ): 3/3.3V
• Operating Temp Range: -40C to 85C
• Package Type: TSOP
• Sync/async: Asynchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 16b
• Number Of Words: 1M
• Supply Current: 18mA
• Mounting: Surface Mount
• Pin Count: 48
• Lead Free Status / Rohs Status: Not Compliant

28F008/800B3, 28F016/160B3, 28F320B3, 28F640B3
11.2
56
Code
Table 26. Command Codes and Descriptions (Sheet 2 of 2)
B0
Table 27. Read Identifier Table
70
50
90
Program / Erase
Read Identifier
Device Mode
Read Status
Clear Status
NOTE: See
Read Identifier
To read the manufacturer and device codes, the device must be in read-identifier mode, which can
be reached by writing the Read Identifier command (90H). Once in read-identifier mode, A
outputs the manufacturer’s identification code, and A
27) Note: A
Suspend
Register
Register
28F004B3
28F400B3
28F008B3
28F800B3
28F016B3
28F160B3
28F320B3
28F640B3
Size
Chapter 14.0, “Write State Machine Current/Next States,”
1
–A
Issuing this command will begin to suspend the currently executing Program/Erase operation.
The Status Register will indicate when the operation has been successfully suspended by
setting either the program suspend (SR.2) or erase suspend (SR.6), and the WSM status bit
(SR.7) to a “1” (ready). The WSM will continue to idle in the SUSPEND state, regardless of the
state of all input-control pins except RP#, which will immediately shut down the WSM and the
remainder of the chip, if it is driven to V
Program” on page 58
This command places the device into Read-Status Register mode. Reading the device will
output the contents of the Status Register, regardless of the address presented to the device.
The device automatically enters this mode after a Program or Erase operation has been
initiated. See
The WSM can set the block-lock status (SR.1), V
erase status (SR.5) bits in the Status Register to “1,” but it cannot clear them to “0.” Issuing this
command clears those bits to “0.”
Puts the device into the intelligent-identifier-read mode, so that reading the device will output
the manufacturer and device codes (A
address inputs must be 0). See Section
Mfr. ID
0089H
0089H
0089H
21
= 0. To return to read-array mode, write the Read-Array command (FFH).
Section 11.3, “Read Status Register” on page
-T (Top Boot)
and
8894H
8892H
8890H
8896H
8898H
D4H
D2H
D0H
Section 11.4.1, “Suspending and Resuming Program” on page
Device Identifier
0
IL
= 0 for manufacturer, A
Section 11.2, “Read Identifier” on page
. See
Description
0
-B (Bottom Boot)
= 1 outputs the device identifier (see
Section 11.4.1, “Suspending and Resuming
PP
8895H
8893H
8891H
8897H
8899H
D5H
D3H
D1H
status (SR.3), program status (SR.4), and
for mode transition information.
57.
0
= 1 for device, all other
56.
Datasheet
0
Table
= 0
58.