AT32UC3A1256AU Atmel Corporation, AT32UC3A1256AU Datasheet - Page 523

• Manufacturer Part Number: AT32UC3A1256AU
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A1256AU

• Flash (kbytes): 256 Kbytes
• Pin Count: 100
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 69
• Ext Interrupts: 69
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 1
• Uart: 4
• Ssc: 1
• Ethernet: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 64
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Operating Voltage (vcc): 3.0-3.6 or (1.65-1.95+3.0-3.6)
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 10
• Output Compare Channels: 16
• Input Capture Channels: 6
• Pwm Channels: 13
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

32058K AVR32-01/12
30.7.3.3
30.7.3.4
30.7.3.5
30.7.3.6
USB Reset
Device Detection
Pipe Reset
Pipe Activation
The controller enters the Suspend state when the USB bus is in a “Suspend” state, i.e. when the
host mode does not generate the “Start of Frame”. In this state, the USB consumption is mini-
mal. The host mode exits the Suspend state when starting to generate the SOF over the USB
line.
A device is detected by the USB controller host mode when D+ or D- is no longer tied low, i.e.
when the device D+ or D- pull-up resistor is connected. To enable this detection, the host con-
troller has to provide the VBus power supply to the device by setting the VBUSRQ bit (by setting
the VBUSRQS bit).
The device disconnection is detected by the host controller when both D+ and D- are pulled
down.
The USB controller sends a USB bus reset when the firmware sets the RESET bit. The USB
Reset Sent interrupt (RSTI) is raised when the USB reset has been sent. In this case, all the
pipes are disabled and de-allocated.
If the bus was previously in a “Suspend” state (SOFE = 0), the USB controller automatically
switches it to the “Resume” state, the Host Wake-Up interrupt (HWUPI) is raised and the SOFE
bit is set by hardware in order to generate SOFs immediately after the USB reset.
A pipe can be reset at any time by setting its PRSTX bit in the UPRST register. This is recom-
mended before using a pipe upon hardware reset or when a USB bus reset has been sent. This
resets:
The pipe configuration remains active and the pipe is still enabled.
The pipe reset may be associated with a clear of the data toggle sequence. This can be
achieved by setting the RSTDT bit (by setting the RSTDTS bit).
In the end, the firmware has to clear the PRSTX bit to complete the reset operation and to start
using the FIFO.
The pipe is maintained inactive and reset (see
long as it is disabled (PENX = 0). The Data Toggle Sequence bit-field (DTSEQ) is also reset.
The algorithm represented on
•the internal state machine of this pipe;
•the receive and transmit bank FIFO counters;
•all the registers of this pipe (UPCFGX, UPSTAX, UPCONX), except its configuration (ALLOC,
PBK, PSIZE, PTOKEN, PTYPE, PEPNUM, INTFRQ) and its Data Toggle Sequence bit-field
(DTSEQ).
Figure 30-24
must be followed in order to activate a pipe.
Section 30.7.3.5 on page 523
AT32UC3A
for more details) as
523