SMM105 SUMMIT Microelectronics, Inc:, SMM105 Datasheet - Page 4

• Manufacturer Part Number: SMM105
• Description: Single-channel Supply Voltage Marginer And Active Dc Output Controller Microelectronics, Inc.
• Manufacturer: SUMMIT Microelectronics, Inc:

Summit Microelectronics, Inc
PIN DESCRIPTIONS
13,15,16
17,24-27
Number
QFN
Pad
28
10
18
20
14
21
22
23
19
12
11
1
2
4
6
9
7
3
5
8
Number
B3,C3,
D4,D5,
CSP
Ultra
Ball
C2
C5
D2
D1
C1
C4
D3
A3
A1
A2
B2
E1
E2
B5
E4
B4
A5
B1
A4
E3
E5
TM
DATA
Type
PWR
PWR
GND
CLK
CAP
CAP
CAP
Pin
NC
I/O
O
O
I
I
I
I
I
I
I
I
I
SDA
SCL
A2
A1
A0
WP#
FILT_CAP
TRIM_CAP
TRIM
VM
VREF_CNTL
VDD
GND
12VIN
START
READY
VDD_CAP
COMP1
COMP2
FAULT#
NC
Pin Name
I
I
The address pins are biased either to VDD_CAP or GND. When
communicating with the SMM105 over the 2-wire bus these pins
provide a mechanism for assigning a unique bus address.
Write Protect active low input. When asserted, writes to the
configuration registers and general purpose EE are not allowed.
External capacitor input used to filter the VM input.
External capacitor input used for Active Control and margining.
Output voltage used to control and/or margin converter voltages.
Connect to the converter trim input.
Voltage monitor input. Connect to the DC-DC converter positive
sense line or its’ +Vout pin.
Voltage reference input used for DC output control and margining.
VREF_CNTL can be programmed to output the internal 1.25V
reference. Pin should be left open if using VREF internal
Power supply of the part.
Ground of the part. The SMM105 ground pin should be connected
to the ground of the device under control or to a star point ground.
PCB layout should take into consideration ground drops.
12V power supply input internally regulated to either 3.6V or 5.5V.
When using the 3.6V internal regulator option, the 12VIN input can
be as low as 8V. It can be as high as 15V using the 5.5V internal
regulator.
Programmable active high/low input. The START input is used
solely for enabling Active Control and/or margining. There is also
a programmable start delay time, T
control.
Programmable active high/low open drain output indicates that VM
is at its set point. When programmed as an active high output,
READY can also be used as an input. When pulled low, it will latch
the state of the comparator inputs.
External capacitor input used to filter the internal supply rail.
COMP1 and COMP2 are high impedance inputs, each connected
internally to a comparator and compared against the VREF_CNTL
input. Each comparator can be independently programmed to
monitor for UV or OV. The monitor level is set externally with a
resistive voltage divider.
When either of the COMP1 or COMP2 inputs are in fault the open-
drain FAULT# output will be pulled low. A configuration option
exists to disable the FAULT# output while the device is margining.
No Connect. Leave floating; do not connect anything to the NC
pins.
2
2
2068 1.8 09/20/05
C Bi-directional data line
C clock input.
Pin Description
START
to delay ADOC/Margin
Preliminary Information
SMM105
4