PIC16C620 Microchip Technology, PIC16C620 Datasheet - Page 83

• Manufacturer Part Number: PIC16C620
• Description: EPROM-Based 8-Bit CMOS Microcontroller
• Manufacturer: Microchip Technology

12.3 DC CHARACTERISTICS: PIC16C62XA/CR62XA-04 (Commercial, Industrial, Extended)
D001
D001A
D002
D003
D004
D005
D010
D010A
D013
D020
D023
Note 1:
Param
1998 Microchip Technology Inc.
No.
*
†
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and
3: The power down current in SLEEP mode does not depend on the oscillator type. Power down current is measured with
4: For RC osc configuration, current through Rext is not included. The current through the resistor can be estimated by the
5: The
V
V
V
S
V
I
I
These parameters are characterized but not tested.
Data in "Typ" column is at 5.0V, 25 C, unless otherwise stated. These parameters are for design guidance only and are
not tested.
This is the limit to which V
switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current con-
sumption.
The test conditions for all I
OSC1 = external square wave, from rail to rail; all I/O pins tri-stated, pulled to V
MCLR = V
the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
formula Ir = V
base I
DD
PD
Sym
I
I
I
I
DD
DR
POR
VDD
BOR
WDT
BOR
COMP
VREF
DD
current is the additional current consumed when this peripheral is enabled. This current should be added to the
Standard Operating Conditions (unless otherwise stated)
Operating temperature –40 C
Supply Voltage
RAM Data Retention
Voltage (Note 1)
V
ensure Power-on Reset
V
Power-on Reset
Brown-out Detect Voltage
Supply Current (Note 2)
Power Down Current (Note 3)
or I
DD
DD
DD
PD
; WDT enabled/disabled as specified.
WDT Current (Note 5)
Brown-out Reset Current
(Note 5)
Comparator Current for each
Comparator (Note 5)
V
rise rate to ensure
DD
start voltage to
REF
measurement.
/2Rext (mA) with Rext in k .
Characteristic
Current (Note 5)
DD
DD
can be lowered in SLEEP mode without losing RAM data.
measurements in active operation mode are:
PIC16C62XA/CR62XA-20 (Commercial, Industrial, Extended)
PIC16LC62XA/LCR62XA-04 (Commercial, Industrial)
PIC16LC62XA/LCR62XA-20 (Commercial, Industrial)
–40 C
0 C
Preliminary
0.05*
Min
3.0
4.5
3.7
3.7
T
T
T
–
–
–
–
–
–
–
–
–
–
A
A
A
+85 C for industrial and
+70 C for commercial and
+125 C for extended
Typ† Max Units
1.5*
V
4.0
4.0
1.2
3.0
1.0
6.0
35
75
60
90
–
-
-
SS
150
200
5.5
5.5
4.3
4.4
2.0
7.5
2.5
70
15
10
12
75
–
–
–
V/ms See section on power-on reset for details
mA
mA
V
V
V
V
V
A
A
A
A
A
A
A
A
DD
XT, RC and LP osc configuration
HS osc configuration
Device in SLEEP mode
See section on power-on reset for details
BOREN configuration bit is cleared
(Extended)
XT and RC osc configuration
F
(Note 4)
LP osc configuration, PIC16C62XA-04
only
F
HS osc configuration
F
V
(125 C)
V
(125 C)
BOR enabled, V
V
V
OSC
OSC
OSC
DD
DD
DD
DD
DD
or V
=4.0V, WDT disabled
=4.0V
= 4.0V
= 4.0V
,
= 4 MHz, V
= 32 kHz, V
= 20 MHz, V
SS
.
PIC16C62X
Conditions
DD
DD
DD
DD
= 5.0V
= 5.5V, WDT disabled
= 4.0V, WDT disabled
= 5.5V, WDT disabled
DS30235G-page 83