CAT25320 CATALYST [Catalyst Semiconductor], CAT25320 Datasheet - Page 5

no-image

CAT25320

Manufacturer Part Number
CAT25320
Description
32-Kb SPI Serial CMOS EEPROM
Manufacturer
CATALYST [Catalyst Semiconductor]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
CAT25320LI-G
Manufacturer:
ON Semiconductor
Quantity:
20
Part Number:
CAT25320VI
Quantity:
97
Part Number:
CAT25320VI-GT3
Manufacturer:
ON Semiconductor
Quantity:
3 500
Part Number:
CAT25320VI-GT3
Manufacturer:
ON/安森美
Quantity:
20 000
Company:
Part Number:
CAT25320VI-GT3
Quantity:
2 250
Company:
Part Number:
CAT25320VI-GT3
Quantity:
120
Company:
Part Number:
CAT25320VI-GT3
Quantity:
3 000
Part Number:
CAT25320VIG
Manufacturer:
NEC
Quantity:
5 126
Part Number:
CAT25320VP2I-GT3
Manufacturer:
ON Semiconductor
Quantity:
6 800
Part Number:
CAT25320VP2IGTKK
Manufacturer:
ON/安森美
Quantity:
20 000
Part Number:
CAT25320YI-GT3
Manufacturer:
CATALYST
Quantity:
20 000
Company:
Part Number:
CAT25320YI-GT3
Quantity:
101
Company:
Part Number:
CAT25320YI-GT3
Quantity:
101
STATUS REGISTER
The Status Register, as shown in Table 2, contains a
number of status and control bits.
The RDY
busy with a write operation. This bit is automatically
set to 1 during an internal write cycle, and reset to 0
when the device is ready to accept commands. For
the host, this bit is read only.
The WEL (Write Enable Latch) bit is set/reset by the
WREN/WRDI commands. When set to 1, the device is
in a Write Enable state and when set to 0, the device
is in a Write Disable state.
The BP0 and BP1 (Block Protect) bits determine
which blocks are currently write protected. They are
set by the user with the WRSR command and are
Table 2. Status Register
Table 3. Block Protection Bits
Table 4. Write Protect Conditions
© 2007 Catalyst Semiconductor, Inc.
Characteristics subject to change without notice
WPEN
¯¯¯¯ (Ready) bit indicates whether the device is
WPEN
7
BP1
Status Register Bits
0
0
1
1
X
X
0
0
1
1
6
0
BP0
0
1
0
1
High
High
Low
Low
¯¯¯
WP
X
X
5
0
Array Address Protected
WEL
0
1
0
1
0
1
4
0
0000-0FFF
0C00-0FFF
0800-0FFF
None
5
non-volatile. The user is allowed to protect a quarter,
one half or the entire memory, by setting these bits
according to Table 3. The protected blocks then
become read-only.
The WPEN (Write Protect Enable) bit acts as an
enable for the WP
enabled when the WP
is 1. This condition prevents writing to the status
register and to the block protected sections of
memory. While hardware write protection is active,
only the non-block protected memory can be written.
Hardware write protection is disabled when the WP
pin is high or the WPEN bit is 0. The WPEN bit, WP
pin and WEL bit combine to either permit or inhibit
Write operations, as detailed in Table 4.
Protected
Protected
Protected
Protected
Protected
Protected
Protected
BP1
Blocks
3
¯¯¯ pin. Hardware write protection is
BP0
¯¯¯ pin is low and the WPEN bit
2
Unprotected
Protected
Protected
Protected
Writable
Writable
Writable
Blocks
Quarter Array Protection
Half Array Protection
Full Array Protection
No Protection
Protection
WEL
1
CAT25320
Doc. No. 1111 Rev. E
Protected
Protected
Protected
Protected
Register
Writable
Writable
Status
¯¯¯¯
RDY
0
¯¯¯
¯¯¯

Related parts for CAT25320