AD14160KB-4 AD [Analog Devices], AD14160KB-4 Datasheet - Page 12

• Manufacturer Part Number: AD14160KB-4
• Description: Quad-SHARC DSP Multiprocessor Family
• Manufacturer: AD [Analog Devices]

AD14160/AD14160L
TARGET BOARD CONNECTOR FOR EZ-ICE PROBE
The ADSP-2106x EZ-ICE Emulator uses the IEEE 1149.1
JTAG test access port of the ADSP-2106x to monitor and con-
trol the target board processor during emulation. The EZ-ICE
probe requires that the AD14160/AD14160L’s CLKIN (op-
tional), TMS, TCK, TRST, TDI, TDO, EMU and GND signals
be made accessible on the target system via a 14-pin connector
(a pin strip header) such as that shown in Figure 6. The EZ-
ICE probe plugs directly onto this connector for chip-on-board
emulation. You must add this connector to your target board
design if you intend to use the ADSP-2106x EZ-ICE. The
length of the traces between the connector and the AD14160/
AD14160L’s JTAG pins should be as short as possible.
Figure 6. Target Board Connector for ADSP-2106x EZ-ICE
Emulator (Jumpers in Place)
CONTROLLER
OTHER
JTAG
KEY (NO PIN)
BTRST
BTMS
CONNECTOR
BTCK
GND
BTDI
GND
EZ-ICE
JTAG
CLKIN
TRST
11
13
EMU
TCK
TMS
TDO
1
3
5
7
9
TOP VIEW
TDI
9
Figure 7. JTAG Scan Path Connections for the AD14160/AD14160L
OPTIONAL
14
10
12
2
4
6
8
TDI
SHARC_A
EMU
TCK
TRST
CLKIN (OPTIONAL)
TMS
TDI
TDO
TDO
TDI
SHARC_B
TDO
–12–
TDI
SHARC_C
The 14-pin, 2-row pin strip header is keyed at the Pin 3 location;
Pin 3 must be removed from the header. The pins must be
0.025 inch square and at least 0.20 inch in length. Pin spacing
should be 0.1
vendors such as 3M, McKenzie and Samtec.
The BTMS, BTCK, BTRST and BTDI signals are provided so
that the test access port can also be used for board-level testing.
When the connector is not being used for emulation, place
jumpers between the Bxxx pins and the xxx pins as shown in
Figure 6. If you are not going to use the test access port for
board testing, tie BTRST to GND and tie or pull up BTCK to
V
BTRST on the connector) or held low for proper operation of
the AD14160/AD14160L. None of the Bxxx pins (Pins 5, 7, 9,
11) are connected on the EZ-ICE probe.
The JTAG signals are terminated on the EZ-ICE probe as follows:
Signal
TMS
TCK
TRST
TDI
TDO
CLKIN
EMU
*TRST is driven low until the EZ-ICE probe is turned on by the EZ-ICE
Figure 7 shows JTAG scan path connections for the multi-
processor system.
software (after the invocation command).
DD
. The TRST pin must be asserted after power-up (through
TDO
Termination
Driven through 22
Driven at 10 MHz through 22
3.2 mA Driver)
Driven by Open-Drain Driver* (Pulled Up by On-Chip
20 k Resistor)
Driven by 16 mA/3.2 mA Driver
One TTL Load, No Termination
One TTL Load, No Termination (Optional Signal)
4.7 k Pull-Up Resistor, One TTL Load (Open-Drain
Output from ADSP-2106x)
TDI
SHARC_D
0.1 inches. Pin strip headers are available from
TDO
Resistor (16 mA/3.2 mA Driver)
TDI
JTAG DEVICE
(OPTIONAL)
TDO
Resistor (16 mA/
TDI
ADSP-2106x
#n
REV. A
TDO