ACPL-P302-000E Avago Technologies US Inc., ACPL-P302-000E Datasheet - Page 7

• Manufacturer Part Number: ACPL-P302-000E
• Description: OPTOCOUPLER W/GAASP LED 6-SOIC
• Manufacturer: Avago Technologies US Inc.

Specifications of ACPL-P302-000E

• Output Type: Push-Pull, Totem-Pole
• Package / Case: SO-6
• Voltage - Isolation: 3750Vrms
• Number Of Channels: 1, Unidirectional
• Current - Output / Channel: 400mA
• Propagation Delay High - Low @ If: 300ns @ 7mA
• Current - Dc Forward (if): 12mA
• Input Type: DC
• Mounting Type: Surface Mount
• Fall Time: 50 ns
• Rise Time: 50 ns
• Configuration: 1 Channel
• Isolation Voltage: 3750 Vrms
• Maximum Forward Diode Voltage: 1.8 V
• Minimum Forward Diode Voltage: 1.2 V
• Maximum Reverse Diode Voltage: 5 V
• Maximum Forward Diode Current: 12 mA
• Maximum Power Dissipation: 250 mW
• Maximum Operating Temperature: + 100 C
• Minimum Operating Temperature: - 40 C
• Number Of Elements: 1
• Forward Voltage: 1.8V
• Forward Current: 25mA
• Operating Temp Range: -40C to 100C
• Power Dissipation: 250mW
• Propagation Delay Time: 700ns
• Pin Count: 6
• Mounting: Surface Mount
• Reverse Breakdown Voltage: 5V
• Operating Temperature Classification: Industrial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Table 7. Package Characteristics
Notes:
1. Derate linearly above 70°C free air temperature at a rate of 0.3 mA/°C.
2. Maximum pulse width = 10 Ps, maximum duty cycle = 0.2%. This value is intended to allow for component tolerances for designs with I
3. Derate linearly above 85°C, free air temperature at the rate of 4.0 mW/°C.
4. Input power dissipation does not require derating.
5. Maximum pulse width = 50 Ps, maximum duty cycle = 0.5%.
6. In this test, V
7. Maximum pulse width = 1 ms, maximum duty cycle = 20%.
8. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 4500 V
9. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 Vrms for 1 second (leakage detection
10. Device considered a two-terminal device: pins on input side shorted together and pins on output side shorted together.
11. PDD is the difference between t
12. Common mode transient immunity in the high state is the maximum tolerable |dV
13. Common mode transient immunity in a low state is the maximum tolerable |dV
14. This load condition approximates the gate load of a 1200 V/20 A IGBT.
15. The power supply current increases when operating frequency and Q
7
Parameter
Input-Output Momentary
Withstand Voltage
Input-Output Resistance
Input-Output Capacitance
minimum = 0.2 A. See Application section for additional details on limiting I
current limit I
Insulation Characteristics Table, if applicable.
current limit II-O < 5 A). This test is performed before 100% production test for partial discharge (method B) shown in the IEC/EN/DIN EN 60747-5-2
Insulation Characteristics Table, if applicable.
will remain in the high state (i.e. V
will remain in a low state (i.e. V
OH
I-O
is measured with a DC load current. When driving capacitive load V
< 5 PA). This test is performed before 100% production test for partial discharge (method B) shown in the IEC/EN/DIN EN 60747-5-2
O
PHL
Symbol
R
V
C
< 1.0 V).
ISO
I-O
I-O
O
and t
> 15.0 V).
PLH
ACPL-P302
ACPL-W302
between any two parts or channels under the same test conditions.
Min.
3750
5000
g
Typ.
10
0.6
of the driven IGBT increases.
12
OL
peak.
CM
Max.
CM
/dt| of the common mode pulse, V
OH
/dt| of the common mode pulse V
will approach V
Units
V
pF
rms
Test Conditions
T
RH < 50% for 1 min.
V
Freq=1 MHz
A
I-O
CC
= 25°C,
= 500 V
as I
OH
rms
approaches zero amps.
for 1 second (leakage detection
CM
CM
, to assure that the output
to assure that the output
Fig.
Note
8, 10
9, 10
10
O
peak