20-101-0303 Rabbit Semiconductor, 20-101-0303 Datasheet - Page 110
20-101-0303
Manufacturer Part Number
20-101-0303
Description
SMARTSCREEN OP7100 W/TOUCHSCREEN
Manufacturer
Rabbit Semiconductor
Datasheet
1.101-0303.pdf
(126 pages)
Specifications of 20-101-0303
Display Type
STN - Super-Twisted Nematic
Viewing Area
121.00mm L x 91.00mm W
Backlight
CCFL - White
Dot Pitch
0.36mm x 0.36mm
Dot Pixels
320 x 240 (QVGA)
Interface
Serial
Product
Prototyping Accessories
Processor Type
Z180
Sram
128 KB
Flash
512 KB
Number Of I/os
16
Backup Battery
3 V Lithium Coin Type
Operating Voltage
10 V to 30 V
Power Consumption
4.5 W
Interface Type
Ethernet
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Display Mode
-
Dot Size
-
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Other names
20-101-0303
20-101-303
20-101-303
316-1175
20-101-303
20-101-303
316-1175
- Current page: 110 of 126
- Download datasheet (780Kb)
Introduction
The SIB is an interface adapter used to program the OP7100. The SIB is
contained in an ABS plastic enclosure, making it rugged and reliable. The
SIB enables the OP7100 to communicate with Dynamic C via the Z180’s
clocked serial I/O (CSI/O) port, freeing the OP7100’s serial ports for use
by the application during programming and debugging.
The SIB’s 8-pin cable plugs into the target OP7100’s processor via header
J4 on the OP7100, which is accessed by removing the back cover from the
OP7100, and a 6-conductor RJ-12 phone cable connects the SIB to the
host PC. The SIB automatically selects its baud rate to match the commu-
nication rates established by the host PC (9600, 19,200, or 57,600 bps).
However, the SIB determines the host’s communication baud rate only on
the first communication after reset. To change baud rates, change the COM
baud rate, reset the target OP7100 (which also resets the SIB), then select
Reset Target
The SIB receives power and resets from the target OP7100 via the 8-pin
connector J1. Therefore, do not unplug the SIB from the target OP7100
while power is applied. To do so could damage both the OP7100 and the
SIB; additionally, the target may reset.
The SIB consumes approximately 60 mA from the +5 V supply. The target-
system current consumption therefore increases by this amount while the
SIB is connected to the OP7100.
When the OP7100 is powered up or reset with the SIB attached, it is
automatically in the program mode. To operate the OP7100 in the run
mode, remove power, disconnect the SIB, and re-apply power to the
OP7100.
110
Serial Interface Board 2
Chapter 2 provides detailed information on connecting the SIB
to the OP7100.
Never connect or disconnect the SIB with power applied to
the OP7100.
from Dynamic C.
OP7100
Related parts for 20-101-0303
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BRD BL2500 29.4MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY PROG OP670
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
DISPLAY GRAPHIC 12KEY ETH OP6700
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2030
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BOARD ETH BL2010
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
MODULE OP6810 W/O ETH/MEM EXPANS
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2020
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2010 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER BL2020 W/FRICTION LOCK
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD BL2500 44.2MHZ
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
COMPUTER SGL-BOARD FULL BL2000
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SINGLE-BOARD BL2110
Manufacturer:
Rabbit Semiconductor
Part Number:
Description:
COMPUTER SGL-BRD 29.4MHZ BL2610
Manufacturer:
Rabbit Semiconductor
Datasheet:
Part Number:
Description:
INTERFACE OP6800 512K FLASH&SRAM
Manufacturer:
Rabbit Semiconductor
Datasheet: