PS11017 Powerex Inc, PS11017 Datasheet - Page 2

• Manufacturer Part Number: PS11017
• Description: IC CONV AC-DC 3-PHASE 600V 50A
• Manufacturer: Powerex Inc

Specifications of PS11017

• Voltage - Output: 600V
• Number Of Outputs: 1
• Power (watts): 30000W
• Applications: Commercial
• Power Supply Type: Switching (Closed Frame)
• Voltage - Input: 450VAC
• Mounting Type: Through Hole
• 1st Output: 600 VDC @ 50A
• Size / Dimension: 4.53" L x 2.99" W x 0.8" H (115mm x 76mm x 20.4mm)
• Power (watts) - Rated: 30000W
• Operating Temperature: -20°C ~ 100°C
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

CONTROL PART
MAXIMUM RATINGS
INVERTER PART (Including Brake Part)
(Fig. 2)
V
V
V
I
V
I
I
V
V
V
V
I
I
C
F
FO
CL
CO
P(S)
Symbol
Symbol
INTERNAL FUNCTIONS BLOCK DIAGRAM
I
DH
CC
CC(surge)
P
CIN
FO
CL
(I
C
(I
FP
or V
( I
CP
or V
, V
)
)
CP
DB
N(S)
N
)
Z : Surge absorber.
C : AC filter (Ceramic condenser 2.2~6.5nF)
[Note : Additionally an appropriate Line-to line
surge absorber circuit may become necessary
depending on the application environment].
Supply voltage
Input signal voltage
Fault output supply voltage
Fault output current
Current-limit warning (CL) output voltage
CL output current
Analogue current signal output current
Supply voltage
Supply voltage (surge)
Each output IGBT collector-emitter static voltage
Each output IGBT collector-emitter
switching surge voltage
Each output IGBT collector current
Brake IGBT collector current
Brake diode anode current
AC 200V line input
Brake resistor connection,
Inrush prevention circuit,
Note 1) To prevent chances of signal oscillation, a series resistor (1k ) coupling at each output is recommended.
Note 2) By virtue of integrating an photo-coupler inside the module, direct coupling to CPU, without any external opto or transformer isolation is possible.
Note 3) All outputs are open collector type. Each signal line should be pulled up to plus side of the 5V power supply with approximately 5.1k resistance.
Note 4) The wiring between power DC link capacitor and P/N terminals should be as short as possible to protect the ASIPM against catastrophic high surge voltage.
For extra precaution, a small film snubber capacitor (0.1~0.22 F, high voltage type) is recommended to be mounted close to these P and N DC power input pins.
(Tj = 25 C)
Z
Analogue signal output corresponding to
each phase current (5V line) Note 1)
C
etc.
Item
Item
R
S
T
CU CV CW
Current sensing
circuit
Input signal conditioning
U
P
(5V line) Note 2)
V
P
PWM input
W
Applied between V
C
Applied between U
W
Applied between F
Sink current of F
Applied between CL-GND
Sink current of CL
Sink current of CU · CV · CW
P
Applied between P-N
Applied between P-N, Surge-value
Applied between P-U, V, W, Br or U, V, W,
Br-N
Applied between P-U, V, W, Br or U, V, W,
Br-N
T
Note: “( )” means I
U
C
BV+
N
N
= 25 C
V
· Br-GND
N
P
B
N
-C
W
N
BV–
B
r
, C
CL, FO
(5V line) Note 3)
BW+
Fo Logic
Drive Circuit
Fault output
1
O1
Application Specific Intelligent
, FO
Condition
Condition
-C
Protection
DH
O1
P
2
C
Circuit
· F
, FO
BW–
· V
peak value
-GND, C
· F
3
O2
Power Module
P
Drive Circuit
Protection
O2
· W
· F
circuit
· F
O3
P
Level shifter
BU+
O3
· U
-GND
N
-C
Control supply
· V
fault sense
BU–
T
S
N
,
·
GND
–0.5 ~ 7.5
50 ( 100)
–0.5 ~ 7
–0.5 ~ 7
Ratings
VDH
Ratings
15 (30)
15 (30)
450
500
600
600
20
15
15
INSULATED TYPE
1
FLAT-BASE TYPE
U
W
V
AC 200V line
output
PS11017
M
May 2001
Unit
Unit
mA
mA
mA
V
V
V
V
V
V
V
V
A
A
A