MPC8315E-RDBA Freescale Semiconductor, MPC8315E-RDBA Datasheet - Page 9

• Manufacturer Part Number: MPC8315E-RDBA
• Description: BOARD MPU 8315 POWERQUICC II
• Manufacturer: Freescale Semiconductor
• Series: PowerQUICC II™ PROr
• Type: MPUr

Specifications of MPC8315E-RDBA

• Contents: Board
• Processor To Be Evaluated: MPC8315E
• Data Bus Width: 32 bit
• Interface Type: Ethernet, I2C, SPI, UART
• Operating Supply Voltage: 1.8 V
• For Use With/related Products: MPC8315E
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3.1.2
Table 2
are the recommended and tested operating conditions. Proper device operation outside of these conditions
is not guaranteed.
Freescale Semiconductor
Input voltage
Storage temperature range
Notes:
1. Functional and tested operating conditions are given in
2. Caution: MV
3. Caution: (N,L)V
4. (M,N,L)V
5. NV
6. The max value of supply voltage shoud be selected based on the RGMII mode.
7. NVDD means NVDD1_OFF, NVDD1_ON, NVDD2_OFF, NVDD2_ON, NVDD3_OFF, NVDD4_OFF
8. LVDD means LVDD1_OFF and LVDD2_ON
SerDes internal digital power
SerDes internal digital power
SerDes I/O digital power
SerDes I/O digital power
SerDes analog power for PLL
SerDes analog power for PLL
Dedicated 3.3 V analog power for USB PLL
functional operation at the maximums is not guaranteed. Stresses beyond those listed may affect device reliability or cause
permanent damage to the device.
power-on reset and power-down sequences.
during power-on reset and power-down sequences.
shown in Figure 3.
IN
provides the recommended operating conditions for theMPC8315E. Note that the values in
on the PCI interface may overshoot/undershoot according to the PCI Electrical Specification for 3.3-V operation, as
IN
Power Supply Voltage Specification
and MVREF may overshoot/undershoot to a voltage and for a maximum duration as shown in
IN
Characteristic
must not exceed GVDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms during
IN
DDR DRAM signals
DDR DRAM reference
eTSEC signals
Local bus, DUART, SYS_CLKIN, system
control and power management, I
JTAG signals
PCI
SATA_CLKIN
must not exceed (N,L)VDD by more than 0.3 V. This limit may be exceeded for a maximum of 20 ms
MPC8315E PowerQUICC
Characteristic
Table 1. Absolute Maximum Ratings
Table 2. Recommended Operating Conditions
™
II Pro Processor Hardware Specifications, Rev. 0
USB_PLL_PWR3
XCOREVDD
XCOREVSS
2
XPADVDD
XPADVSS
C, and
SDAVDD
SDAVSS
Symbol
Table
2. Absolute maximum ratings are stress ratings only, and
Symbol
MVREF
MV
T
NV
NV
NV
LV
Recommended
STG
3.3 ± 165mv
IN
1.0 ± 50 mv
1.0 ± 50 mv
1.0 ± 50 mv
IN
IN
IN
IN
Value
1
0.0
0.0
0.0
(continued)
1
–0.3 to (GVDD + 0.3)
–0.3 to (GVDD + 0.3)
–0.3 to (NVDD + 0.3)
–0.3 to (NVDD + 0.3)
–0.3 to (NVDD + 0.3)
–0.3 to (LVDD + 0.3)
Max Value
Unit
–55 to150
V
V
V
V
V
V
V
Status in D3
Warm mode
Switched Off
Switched Off
Switched Off
Switched Off
Electrical Characteristics
—
—
—
Figure
Unit
°C
V
V
V
V
V
V
2.
Notes
Table 2
—
—
—
—
—
—
—
Notes
2, 4
2, 4
3, 4
3, 4
3, 4
—
5
9