PIC12F629-I/P Microchip Technology, PIC12F629-I/P Datasheet - Page 23

• Manufacturer Part Number: PIC12F629-I/P
• Description: IC MCU CMOS FLASH-BASE 8BIT 8DIP
• Manufacturer: Microchip Technology
• Series: PIC® 12Fr

Specifications of PIC12F629-I/P

• Program Memory Type: FLASH
• Program Memory Size: 1.75KB (1K x 14)
• Package / Case: 8-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Peripherals: POR, WDT
• Number Of I /o: 5
• Eeprom Size: 128 x 8
• Ram Size: 64 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC12F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 64 B
• Interface Type: RS- 232/USB
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 6
• Number Of Timers: 2
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
• Minimum Operating Temperature: - 40 C
• Data Rom Size: 128 B
• Height: 3.3 mm
• Length: 9.27 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2 V
• Width: 6.35 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM163029 - BOARD PICDEM FOR MECHATRONICSAC124001 - MODULE SKT PROMATEII 8DIP/SOIC
• Data Converters: -
• Connectivity: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

3.2.2
Each of the GPIO pins is individually configurable as an
interrupt-on-change pin. Control bits IOC enable or
disable the interrupt function for each pin. Refer to
Register 3-4. The interrupt-on-change is disabled on a
Power-on Reset.
For enabled interrupt-on-change pins, the values are
compared with the old value latched on the last read of
GPIO. The ‘mismatch’ outputs of the last read are OR’d
together to set, the GP Port Change Interrupt flag bit
(GPIF) in the INTCON register.
REGISTER 3-4:
 2010 Microchip Technology Inc.
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7-6
bit 5-0
Note 1:
U-0
—
Global Interrupt Enable (GIE) must be enabled for individual interrupts to be recognized.
INTERRUPT-ON-CHANGE
Unimplemented: Read as ‘0’
IOC<5:0>: Interrupt-on-Change GPIO Control bits
1 = Interrupt-on-change enabled
0 = Interrupt-on-change disabled
U-0
—
IOC: INTERRUPT-ON-CHANGE GPIO REGISTER (ADDRESS: 96h)
W = Writable bit
‘1’ = Bit is set
R/W-0
IOC5
R/W-0
IOC4
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-0
This interrupt can wake the device from Sleep. The
user, in the Interrupt Service Routine, can clear the
interrupt in the following manner:
a)
b)
A mismatch condition will continue to set flag bit GPIF.
Reading GPIO will end the mismatch condition and
allow flag bit GPIF to be cleared.
IOC3
Note:
Any read or write of GPIO. This will end the
mismatch condition.
Clear the flag bit GPIF.
If a change on the I/O pin should occur
when the read operation is being executed
(start of the Q2 cycle), then the GPIF inter-
rupt flag may not get set.
R/W-0
IOC2
PIC12F629/675
x = Bit is unknown
R/W-0
IOC1
DS41190G-page 23
R/W-0
IOC0
bit 0