PIC16LF723-I/ML Microchip Technology, PIC16LF723-I/ML Datasheet - Page 51

• Manufacturer Part Number: PIC16LF723-I/ML
• Description: IC PIC MCU FLASH 8KX14 28-QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 16Fr

Specifications of PIC16LF723-I/ML

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Type: FLASH
• Ram Size: 192 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 11x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Controller Family/series: PIC16LF
• Ram Memory Size: 192Byte
• No. Of Timers: 3
• No. Of Pwm Channels: 2
• Digital Ic Case Style: QFN
• Supply Voltage Range: 1.8V To
• Rohs Compliant: Yes
• Core: PIC
• Processor Series: PIC16LF
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 32 KHz
• Data Ram Size: 192 B
• On-chip Adc: Yes
• Number Of Programmable I/os: 25
• Number Of Timers: 3
• Operating Supply Voltage: 1.8 V to 3.6 V
• Mounting Style: SMD/SMT
• A/d Bit Size: 8 bit
• A/d Channels Available: 11
• Height: 0.88 mm
• Interface Type: I2C, SCI, SPI
• Length: 6 mm
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.3 V
• Width: 6 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

5.0
The PIC16F72X devices differ from the PIC16LF72X
devices due to an internal Low Dropout (LDO) voltage
regulator. The PIC16F72X contain an internal LDO,
while the PIC16LF72X do not.
The lithography of the die allows a maximum operating
voltage of 3.6V on the internal digital logic. In order to
continue to support 5.0V designs, a LDO voltage
regulator is integrated on the die. The LDO voltage
regulator allows for the internal digital logic to operate
at 3.2V, while I/O’s operate at 5.0V (V
The LDO voltage regulator requires an external bypass
capacitor for stability. One of three pins, denoted as
V
capacitor. It is recommended that the capacitor be a
ceramic cap between 0.1 to 1.0 µF. The V
intended to supply power to external loads. An external
voltage regulator should be used if this functionality is
required. In addition, external devices should not
supply power to the V
On power-up, the external capacitor will look like a
large load on the LDO voltage regulator. To prevent
erroneous operation, the device is held in Reset while
a constant current source charges the external
capacitor. After the cap is fully charged, the device is
released from Reset. For more information, refer to
Section 23.0 “Electrical Specifications”.
See Configuration Word 2 register (Register 8-2) for
V
© 2009 Microchip Technology Inc.
CAP
CAP
, can be configured for the external bypass
enable bits.
LOW DROPOUT (LDO)
VOLTAGE REGULATOR
CAP
pin.
DD
).
CAP
pin is not
PIC16F72X/PIC16LF72X
DS41341E-page 51