ATTINY461A-MU Atmel, ATTINY461A-MU Datasheet - Page 127

• Manufacturer Part Number: ATTINY461A-MU
• Description: IC MCU AVR 4K FLASH 20MHZ 32QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY461A-MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Processor Series: ATTINY4x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

13.3.3
13.3.4
8197B–AVR–01/10
SPI Slave Operation Example
Two-wire Mode
The following code demonstrates how to use the USI module as a SPI Slave:
The code is size optimized using only eight instructions (+ ret). The code example assumes that
the DO is configured as output and USCK pin is configured as input in the DDR Register. The
value stored in register r16 prior to the function is called is transferred to the master device, and
when the transfer is completed the data received from the Master is stored back into the r16
Register.
Note that the first two instructions are for initialization, only, and need only be executed once.
These instructions set three-wire mode and positive edge clock. The loop is repeated until the
USI Counter Overflow Flag is set.
The USI Two-wire mode is compliant to the Inter IC (TWI) bus protocol, but without slew rate lim-
iting on outputs and input noise filtering. Pin names used by this mode are SCL and SDA.
Figure 13-4 on page 128
one as slave. It is only the physical layer that is shown since the system operation is highly
dependent of the communication scheme used. The main differences between the master and
slave operation at this level is the serial clock generation which is always done by the master.
Only the slave uses the clock control unit.
Clock generation must be implemented in software, but the shift operation is done automatically
in both devices. Note that clocking only on negative edges for shifting data is of practical use in
this mode. The slave can insert wait states at start or end of transfer by forcing the SCL clock
low. This means that the master must always check if the SCL line was actually released after it
has generated a positive edge.
Since the clock also increments the counter, a counter overflow can be used to indicate that the
transfer is completed. The clock is generated by the master by toggling the USCK pin via the
PORTA register.
init:
...
SlaveSPITransfer:
SlaveSPITransfer_loop:
ldi
sts
sts
ldi
sts
lds
sbrs
rjmp
lds
ret
r16,(1<<USIWM0)|(1<<USICS1)
USICR,r16
USIDR,r16
r16,(1<<USIOIF)
USISR,r16
r16, USISR
r16, USIOIF
SlaveSPITransfer_loop
r16,USIDR
shows two USI units operating in two-wire mode, one as master and
127