ATTINY461A-MU Atmel, ATTINY461A-MU Datasheet - Page 155

• Manufacturer Part Number: ATTINY461A-MU
• Description: IC MCU AVR 4K FLASH 20MHZ 32QFN
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY461A-MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-VQFN Exposed Pad, 32-HVQFN, 32-SQFN, 32-DHVQFN
• Processor Series: ATTINY4x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 16
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8197B–AVR–01/10
• Bit 7:6 – REFS1:REFS0: Voltage Reference Selection Bits
These bits together with the REFS2 bit from the ADC Control and Status Register B (ADCSRB)
select the voltage reference for the ADC, as shown in
Table 15-4.
If these bits are changed during a conversion, the change will not go in effect until this conver-
sion is complete (ADIF in ADCSR is set). Also note, that when these bits are changed, the next
conversion will take 25 ADC clock cycles.
Special care should be taken when changing differential channels. Once a differential channel
has been selected the input stage may take a while to stabilize. It is therefore recommended to
force the ADC to perform a long conversion when changing multiplexer or voltage reference set-
tings. This can be done by first turning off the ADC, then changing reference settings and then
turn on the ADC. Alternatively, the first conversion results after changing reference settings
should be discarded.
It is not recommended to use an external AREF higher than (V
ential gain, as this will affect ADC accuracy.
Internal voltage reference options may not be used if an external voltage is being applied to the
AREF pin.
• Bit 5 – ADLAR: ADC Left Adjust Result
The ADLAR bit affects the presentation of the ADC conversion result in the ADC Data Register.
Write one to ADLAR to left adjust the result. Otherwise, the result is right adjusted. Changing the
ADLAR bit will affect the ADC Data Register immediately, regardless of any ongoing conver-
sions. For a comple te description of this bit, see
on page
• Bits 4:0 – MUX4:0: Analog Channel and Gain Selection Bits
These bits and the MUX5 bit from the ADC Control and Status Register B (ADCSRB) select
which combination of analog inputs are connected to the ADC. In case of differential input, gain
selection is also made with these bits. Selecting the same pin as both inputs to the differential
REFS2
X
X
0
0
1
1
154.
Voltage Reference Selections for ADC
REFS1
0
0
1
1
1
1
REFS0
0
1
0
1
0
1
Voltage Reference Selection
V
disconnected from AREF
External voltage reference at AREF pin,
internal voltage reference turned off
Internal 1.1V voltage reference
Reserved
Internal 2.56V voltage reference (
without external bypass capacitor,
disconnected from AREF
Internal 2.56V voltage reference (
with external bypass capacitor at AREF pin
CC
used as voltage reference,
“ADCL and ADCH – The ADC Data Register”
Table
15-4.
CC
- 1V) for channels with differ-
V
V
CC
CC
> 3.0V),
> 3.0V),
155