ATMEGA8515L-8AU Atmel, ATMEGA8515L-8AU Datasheet - Page 56

• Manufacturer Part Number: ATMEGA8515L-8AU
• Description: IC AVR MCU 8K 8MHZ 3V 44TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8515L-8AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: EBI/EMI, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 35
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-TQFP, 44-VQFP
• Processor Series: ATMEGA8x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

56
ATmega8515(L)
When the BOOTRST Fuse is unprogrammed, the Boot section size set to 2K bytes and
the IVSEL bit in the GICR Register is set before any interrupts are enabled, the most
typical and general program setup for the Reset and Interrupt Vector Addresses is:
When the BOOTRST Fuse is programmed and the Boot section size set to 2K bytes, the
most typical and general program setup for the Reset and Interrupt Vector Addresses is:
When the BOOTRST Fuse is programmed, the Boot section size set to 2K bytes and the
IVSEL bit in the GICR Register is set before any interrupts are enabled, the most typical
and general program setup for the Reset and Interrupt Vector Addresses is:
Address Labels
$000
$001
$002
$003
$004
$005
;
.org $C02
$C02
$C04
...
$C2A
Handler
Address Labels
.org $002
$001
$002
...
$010
Handler
;
.org $C00
$C00
$C01
$C02
$C03
$C04
$C05
Address Labels
.org $C00
$C00
$C01
$C02
...
$C10
Handler
;
$C11
RESET:
....
....
RESET:
....
RESET:
Code
ldi
out
ldi
out
sei
<instr>
rjmp EXT_INT0
rjmp EXT_INT1
..
rjmp SPM_RDY
Code
rjmp EXT_INT0
rjmp EXT_INT1
..
rjmp SPM_RDY
ldi
out
ldi
out
sei
<instr>
Code
rjmp RESET
rjmp EXT_INT0
rjmp EXT_INT1
..
rjmp SPM_RDY
ldi
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
r16,high(RAMEND); Main program start
SPH,r16
r16,low(RAMEND)
SPL,r16
r16,high(RAMEND); Main program start
xxx
xxx
; Set Stack Pointer to top of RAM
; Enable interrupts
; IRQ0 Handler
; IRQ1 Handler
;
; Store Program memory Ready
Comments
; IRQ0 Handler
; IRQ1 Handler
;
; Store Program memory Ready
; Set Stack Pointer to top of RAM
; Enable interrupts
; Reset handler
; IRQ0 Handler
; IRQ1 Handler
;
; Store Program memory Ready
Comments
Comments
2512K–AVR–01/10