PIC18F27J53-I/SP Microchip Technology, PIC18F27J53-I/SP Datasheet - Page 340

• Manufacturer Part Number: PIC18F27J53-I/SP
• Description: IC PIC MCU 128KB FLASH 28SPDIP
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F27J53-I/SP

• Program Memory Type: FLASH
• Program Memory Size: 128KB (64K x 16)
• Package / Case: *
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, LIN, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Ram Size: 3.8K x 8
• Voltage - Supply (vcc/vdd): 2.15 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3.8 KB
• Interface Type: I2C, SPI, USART
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 16
• Number Of Timers: 8
• Operating Supply Voltage: 2.15 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• Controller Family/series: PIC18
• Cpu Speed: 48MHz
• Embedded Interface Type: I2C, SPI, USART
• Digital Ic Case Style: DIP
• Supply Voltage Range: 1.8V To 5.5V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F47J53 FAMILY
20.5.17.1
During a Start condition, a bus collision occurs if:
a)
b)
During a Start condition, both the SDAx and the SCLx
pins are monitored.
If the SDAx pin is already low, or the SCLx pin is
already low, then all of the following occur:
• The Start condition is aborted
• The BCLxIF flag is set
• The MSSP module is reset to its inactive state
The Start condition begins with the SDAx and SCLx
pins deasserted. When the SDAx pin is sampled high,
the BRG is loaded from SSPxADD<6:0> and counts
down to 0. If the SCLx pin is sampled low while SDAx
is high, a bus collision occurs because it is assumed
that another master is attempting to drive a data ‘1’
during the Start condition.
FIGURE 20-28:
DS39964B-page 340
(Figure 20-28)
SDAx
SCLx
SEN
BCLxIF
S
SSPxIF
SDAx or SCLx is sampled low at the beginning
of the Start condition (Figure 20-28).
SCLx is sampled low before SDAx is asserted
low (Figure 20-29).
Bus Collision During a Start
Condition
condition if SDAx = 1, SCLx = 1
Set SEN, enable Start
BUS COLLISION DURING START CONDITION (SDAx ONLY)
SDAx sampled low before
Start condition. Set BCLxIF.
S bit and SSPxIF set because
SDAx = 0, SCLx = 1.
SDAx goes low before the SEN bit is set.
Set BCLxIF,
S bit and SSPxIF set because
SDAx = 0, SCLx = 1.
Preliminary
SSPxIF and BCLxIF are
cleared in software
If the SDAx pin is sampled low during this count, the
BRG is reset and the SDAx line is asserted early
(Figure 20-30). If, however, a ‘1’ is sampled on the
SDAx pin, the SDAx pin is asserted low at the end of
the BRG count. The BRG is then reloaded and counts
down to 0. If the SCLx pin is sampled as ‘0’ during this
time, a bus collision does not occur. At the end of the
BRG count, the SCLx pin is asserted low.
Note:
SEN cleared automatically because of bus collision.
MSSPx module reset into Idle state.
The reason that a bus collision is not a fac-
tor during a Start condition is that no two
bus masters can assert a Start condition at
the exact same time. Therefore, one mas-
ter will always assert SDAx before the
other. This condition does not cause a bus
collision because the two masters must be
allowed to arbitrate the first address
following the Start condition. If the address
is the same, arbitration must be allowed to
continue into the data portion, Repeated
Start or Stop conditions.
SSPxIF and BCLxIF are
cleared in software
 2010 Microchip Technology Inc.