PIC18F8310-I/PT Microchip Technology, PIC18F8310-I/PT Datasheet - Page 98

• Manufacturer Part Number: PIC18F8310-I/PT
• Description: IC PIC MCU FLASH 4KX16 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F8310-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 8KB (4K x 16)
• Package / Case: 80-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 70
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: SPI/I2C/EUSART/AUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 70
• Number Of Timers: 4
• Operating Supply Voltage: 4.2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032
• Minimum Operating Temperature: - 25 C
• On-chip Adc: 12-ch x 10-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT80PT3 - SOCKET TRAN ICE 80MQFP/TQFPAC164320 - MODULE SKT MPLAB PM3 80TQFPAC174011 - MODULE SKT PROMATEII 80TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F6310/6410/8310/8410
8.2.2
Figure 8-2
mode for PIC18F8410 devices. This mode is used for
word-wide memories, which includes some of the
EPROM and Flash type memories. This mode allows
opcode fetches and table reads from all forms of 16-bit
memory and table writes to any type of word-wide
external memories. This method makes a distinction
between TBLWT cycles to even or odd addresses.
During a TBLWT cycle to an even address
(TBLPTR<0> = 0), the TABLAT data is transferred to a
holding latch and the external address data bus is
tri-stated for the data portion of the bus cycle. No write
signals are activated.
FIGURE 8-2:
DS39635C-page 98
Note 1:
shows an example of 16-Bit Word Write
16-BIT WORD WRITE MODE
PIC18F8410
AD<15:8>
A<19:16>
This signal only applies to table writes. See
AD<7:0>
16-BIT WORD WRITE MODE EXAMPLE
WRH
ALE
CE
OE
373
373
Section 7.1 “Table Reads and Table
During
(TBLPTR<0> = 1), the TABLAT data is presented on
the upper byte of the AD<15:0> bus. The contents of
the holding latch are presented on the lower byte of the
AD<15:0> bus.
The WRH signal is strobed for each write cycle; the
WRL pin is unused. The signal on the BA0 pin indicates
the LSb of TBLPTR, but it is left unconnected. Instead,
the UB and LB signals are active to select both bytes.
The obvious limitation to this method is that the table
write must be done in pairs on a specific word boundary
to correctly write a word location.
A<20:1>
D<15:0>
a
TBLWT
Address Bus
Data Bus
Control Lines
D<15:0>
A<x:0>
cycle
 2010 Microchip Technology Inc.
CE
Writes”.
EPROM Memory
to
OE
JEDEC Word
an
WR
odd
(1)
address