PIC24FJ128GA008-I/PT Microchip Technology, PIC24FJ128GA008-I/PT Datasheet - Page 94

• Manufacturer Part Number: PIC24FJ128GA008-I/PT
• Description: IC PIC MCU FLASH 128K 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Fr

Specifications of PIC24FJ128GA008-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (43K x 24)
• Package / Case: 80-TFQFP
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: I²C, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 69
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24FJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: SPI/I2C/USART
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 5
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001, DM240011, DV164033, MA240011, AC164127
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16-ch x 10-bit
• Controller Family/series: PIC24
• No. Of I/o's: 69
• Ram Memory Size: 8KB
• Cpu Speed: 32MHz
• No. Of Timers: 5
• Embedded Interface Type: EUART, I2C, PSP, SPI
• Rohs Compliant: Yes
• Package: 80TQFP
• Device Core: PIC
• Family Name: PIC24
• Maximum Speed: 16 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDDM240011 - KIT STARTER MPLAB FOR PIC24F MCUMA160011 - DAUGHTER BOARD PICDEM LCD 16F91XDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32AC164328 - MODULE SKT FOR 80TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC24FJ128GA FAMILY
7.2
The oscillator source (and operating mode) that is
used at a device Power-on Reset event is selected
using Configuration bit settings. The oscillator Config-
uration bit settings are located in the Configuration
registers
Section 23.1
details.) The Primary Oscillator Configuration bits,
POSCMD1:POSCMD0 (Configuration Word 2<1:0>),
and the Initial Oscillator Select Configuration bits,
FNOSC2:FNOSC0
select the oscillator source that is used at a Power-on
Reset. The FRC primary oscillator with postscaler
(FRCDIV) is the default (unprogrammed) selection.
TABLE 7-1:
7.3
The operation of the oscillator is controlled by three
Special Function Registers:
• OSCCON
• CLKDIV
• OSCTUN
The OSCCON register (Register 7-1) is the main con-
trol register for the oscillator. It controls clock source
switching, and allows the monitoring of clock sources.
DS39747C-page 92
Fast RC Oscillator with Postscaler
(FRCDIV)
(Reserved)
Low-Power RC Oscillator (LPRC)
Secondary (Timer1) Oscillator
(SOSC)
Primary Oscillator (HS) with PLL
Module (HSPLL)
Primary Oscillator (XT) with PLL
Module (ECPLL)
Primary Oscillator (EC) with PLL
Module (XTPLL)
Primary Oscillator (HS)
Primary Oscillator (XT)
Primary Oscillator (EC)
Fast RC Oscillator with PLL Module
(FRCPLL)
Fast RC Oscillator (FRC)
Note 1:
2:
Oscillator Configuration
Control Registers
Oscillator Mode
in
OSC2 pin function is determined by the OSCIOFNC Configuration bit.
This is the default oscillator mode for an unprogrammed (erased) device.
the
“Configuration
CONFIGURATION BIT VALUES FOR CLOCK SELECTION
program
(Configuration Word 2<10:8>),
memory
Bits”
Oscillator Source
for
(refer
Secondary
Internal
Internal
Internal
Primary
Primary
Primary
Primary
Primary
Primary
Internal
Internal
further
Preliminary
to
The secondary oscillator, or one of the internal
oscillators, may be chosen by programming these bit
locations.
The Configuration bits allow users to choose between
the various clock modes, shown in Table 7-1.
7.2.1
The FCKSM Configuration bits (Configuration Word 2<7:6>)
are used to jointly configure device clock switching and
the Fail-Safe Clock Monitor (FSCM). Clock switching is
enabled only when FCKSM1 is programmed (‘0’). The
FSCM is enabled only when FCKSM1:FCKSM0 are
both programmed (‘00’).
The Clock Divider register (Register 7-2) controls the
features associated with Doze mode, as well as the
postscaler for the FRC oscillator.
The FRC Oscillator Tune register (Register 7-3) allows
the user to fine tune the FRC oscillator over a range of
approximately ±12%. Each bit increment or decrement
changes the factory calibrated frequency of the FRC
oscillator by a fixed amount.
POSCMD1:
POSCMD0
00
00
00
00
10
01
00
10
01
00
00
00
CLOCK SWITCHING MODE
CONFIGURATION BITS
© 2006 Microchip Technology Inc.
FNOSC2:
FNOSC0
111
110
101
100
011
011
011
010
010
010
001
000
Note
1, 2
1
1
1
1
1