PIC24HJ128GP504-I/PT Microchip Technology, PIC24HJ128GP504-I/PT Datasheet - Page 123

• Manufacturer Part Number: PIC24HJ128GP504-I/PT
• Description: IC PIC MCU FLASH 128K 44TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ128GP504-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 128KB (43K x 24)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 35
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 13x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 35
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM240001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 13-ch x 12-bit
• Controller Family/series: PIC24
• No. Of I/o's: 35
• Ram Memory Size: 8KB
• Cpu Speed: 40MIPS
• No. Of Timers: 7
• Embedded Interface Type: CAN, I2C, SPI, UART
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1004 - PIC24 BREAKOUT BOARDDM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

REGISTER 9-1:
© 2009 Microchip Technology Inc.
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14-12
bit 11
bit 10-8
bit 7
bit 6
bit 5
bit 4
bit 3
CLKLOCK
Note 1: Writes to this register require an unlock sequence. Refer to Section 39. “Oscillator (Part III)” (DS70308)
R/W-0
U-0
—
2: Direct clock switches between any primary oscillator mode with PLL and FRCPLL mode are not permitted.
in the “dsPIC33F Family Reference Manual” (available from the Microchip website) for details.
This applies to clock switches in either direction. In these instances, the application must switch to FRC mode
as a transition clock source between the two PLL modes.
Unimplemented: Read as ‘0’
COSC<2:0>: Current Oscillator Selection bits (read-only)
000 = Fast RC oscillator (FRC)
001 = Fast RC oscillator (FRC) with PLL
010 = Primary oscillator (XT, HS, EC)
011 = Primary oscillator (XT, HS, EC) with PLL
100 = Secondary oscillator (S
101 = Low-Power RC oscillator (LPRC)
110 = Fast RC oscillator (FRC) with Divide-by-16
111 = Fast RC oscillator (FRC) with Divide-by-n
Unimplemented: Read as ‘0’
NOSC<2:0>: New Oscillator Selection bits
000 = Fast RC oscillator (FRC)
001 = Fast RC oscillator (FRC) with PLL
010 = Primary oscillator (XT, HS, EC)
011 = Primary oscillator (XT, HS, EC) with PLL
100 = Secondary oscillator (S
101 = Low-Power RC oscillator (LPRC)
110 = Fast RC oscillator (FRC) with Divide-by-16
111 = Fast RC oscillator (FRC) with Divide-by-n
CLKLOCK: Clock Lock Enable bit
If clock switching is enabled and FSCM is disabled, (FOSC<FCKSM> = 0b01)
1 = Clock switching is disabled, system clock source is locked
0 = Clock switching is enabled, system clock source can be modified by clock switching
IOLOCK: Peripheral Pin Select Lock bit
1 = Peripherial pin select is locked, write to peripheral pin select registers not allowed
0 = Peripherial pin select is not locked, write to peripheral pin select registers allowed
LOCK: PLL Lock Status bit (read-only)
1 = Indicates that PLL is in lock, or PLL start-up timer is satisfied
0 = Indicates that PLL is out of lock, start-up timer is in progress or PLL is disabled
Unimplemented: Read as ‘0’
CF: Clock Fail Detect bit (read/clear by application)
1 = FSCM has detected clock failure
0 = FSCM has not detected clock failure
IOLOCK
R/W-0
R-0
OSCCON: OSCILLATOR CONTROL REGISTER
y = Value set from Configuration bits on POR
W = Writable bit
‘1’ = Bit is set
COSC<2:0>
LOCK
R-0
R-0
OSC
OSC
R-0
U-0
)
)
Preliminary
—
(2)
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/C-0
U-0
CF
—
R/W-y
(1)
U-0
—
NOSC<2:0>
x = Bit is unknown
LPOSCEN
R/W-y
R/W-0
DS70293D-page 123
C = Clear only bit
(2)
OSWEN
R/W-0
R/W-y
bit 8
bit 0