PIC32MX360F512L-80I/PT Microchip Technology, PIC32MX360F512L-80I/PT Datasheet - Page 5

• Manufacturer Part Number: PIC32MX360F512L-80I/PT
• Description: IC PIC MCU FLASH 512K 100-TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 32MXr

Specifications of PIC32MX360F512L-80I/PT

• Program Memory Type: FLASH
• Program Memory Size: 512KB (512K x 8)
• Package / Case: 100-TFQFP
• Core Processor: MIPS32® M4K™
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: I²C, IrDA, LIN, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 85
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 2.3 V ~ 3.6 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC32MX3xx
• Core: MIPS
• Data Bus Width: 32 bit
• Data Ram Size: 32 KB
• Interface Type: I2C , SPI , UART
• Maximum Clock Frequency: 80 MHz
• Number Of Programmable I/os: 85
• Number Of Timers: 5 x 16 bit
• Operating Supply Voltage: 2.3 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, DM320001, DM320002, MA320001
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• Controller Family/series: PIC32
• No. Of I/o's: 85
• Ram Memory Size: 32KB
• Cpu Speed: 80MHz
• No. Of Timers: 6
• Embedded Interface Type: EUART, I2C, PSP, SPI
• No. Of Pwm Channels: 5
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 876-1000 - PIC32 BREAKOUT BOARDAC244003 - TEST BD MPLAB REAL ICE LOOPBACKAC244006 - KIT MPLAB REAL ICE TRACEDM320001 - KIT EVAL PIC32 STARTERAC164333 - MODULE SKT FOR PM3 100QFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

4.2
Another possible interface is the 2-wire ICSP port.
Table 4-2 lists the required pin connections. This inter-
face uses the following 2 communication lines to trans-
fer data to and from the PIC32MX device being
programmed:
• PGCx – Serial Program Clock
• PGDx – Serial Program Data
These signals are described in the following two
sections. Refer to the specific device data sheet for the
connection of the signals to the chip pins.
4.2.1
PGCx is the clock that controls the updating of the TAP
controller and the shifting of data through the Instruc-
tion or selected Data register(s). PGCx is independent
of the processor clock, with respect to both frequency
and phase.
4.2.2
PGDx is the data input/output to the Instruction or
selected Data Register(s), it is also the control signal
for the TAP controller. This signal is sampled on the
falling edge of PGC for some TAP controller states.
4.3
All devices in the PIC32MX family are dual voltage
supply designs: one supply for the core and peripherals
and another for the I/O pins. Some devices contain an
on-chip regulator to eliminate the need for two external
voltage supplies.
All of the PIC32MX devices power their core digital
logic at a nominal 1.8V. This may create an issue for
designs that are required to operate at a higher typical
voltage, such as 3.3V. To simplify system design, all
devices in the PIC32MX family incorporate an on-chip
regulator that allows the device to run its core logic from
V
TABLE 4-2:
© 2010 Microchip Technology Inc.
MCLR
ENVREG
V
V
V
PGC1
PGD1
PGC2
PGD2
Legend: I = Input
Note 1:
DD
DD
SS
DDCORE
.
Pin Name
and AV
and AV
Device
2-Wire Interface
Power Requirements
All power supply and ground pins must be connected, including analog supplies (AV
SERIAL PROGRAM CLOCK (PGC
SERIAL PROGRAM DATA (PGD
SS
DD
(1)
(1)
2-WIRE INTERFACE PINS
MCLR
N/A
V
V
N/A
PGC
PGD
PGC
PGD
Programmer
DD
SS
Pin Name
O = Output
Pin Type
I/O
I/O
P
P
P
P
I
I
I
X
)
X
)
Programming Enable
Enable for On-Chip Voltage Regulator
Power Supply
Ground
Regulated Power Supply for Core
Primary Programming Pin Pair: Serial Clock
Primary Programming Pin Pair: Serial Data
Secondary Programming Pin Pair: Serial Clock
Secondary Programming Pin Pair: Serial Data
The regulator provides power to the core from the other
V
capacitor) must be connected to the V
(Figure 4-2). This helps to maintain the stability of the
regulator. The specifications for core voltage and
capacitance are listed in 20.0 “AC/DC Characteristics
and Timing Requirements”.
FIGURE 4-2:
DD
Note 1: These are typical operating voltages. Refer to
P = Power
pins. A low ESR capacitor (e.g., a tantalum
1.8V
(10 μF typ)
20.0 “AC/DC Characteristics and Timing
Requirements” for the full operating ranges of
V
C
DD
EFC
(1)
Pin Description
and V
(ENVREG tied to ground)
(ENVREG tied to V
3.3V
3.3V
Regulator Disabled
Regulator Enabled
DDCORE
(1)
CONNECTIONS FOR THE
ON-CHIP REGULATOR
V
ENVREG
V
V
V
ENVREG
V
V
.
DD
DDCORE
SS
DD
DDCORE
SS
PIC32MX
PIC32MX
DD
PIC32MX
) and ground (AV
DD
/V
/V
)
CAP
CAP
DS61145G-page 5
DDCORE
SS
pin
).