P89V51RD2FBC,557 NXP Semiconductors, P89V51RD2FBC,557 Datasheet - Page 34

• Manufacturer Part Number: P89V51RD2FBC,557
• Description: IC 80C51 MCU FLASH 64K 44-TQFP
• Manufacturer: NXP Semiconductors
• Series: 89Vr

Specifications of P89V51RD2FBC,557

• Program Memory Type: FLASH
• Program Memory Size: 64KB (64K x 8)
• Package / Case: 44-TQFP, 44-VQFP
• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 32
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: P89V5x
• Core: 80C51
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI/UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 3
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 622-1017 - BOARD 44-ZIF PLCC SOCKET622-1001 - USB IN-CIRCUIT PROG 80C51ISP
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-1291; 935276047557; P89V51RD2FBC

NXP Semiconductors
P89V51RB2_RC2_RD2_5
Product data sheet
Fig 13. Timer 2 in auto-reload mode (DCEN = 0)
OSC
T2 pin
T2EX pin
6
In this mode, there are two options selected by bit EXEN2 in T2CON register. If
EXEN2 = 0, then Timer 2 counts up to 0FFFFH and sets the TF2 (Overflow Flag) bit upon
overflow. This causes the Timer 2 registers to be reloaded with the 16-bit value in
RCAP2L and RCAP2H. The values in RCAP2L and RCAP2H are preset by software
means.
Auto reload frequency when Timer 2 is counting up can be determined from this formula:
Where SupplyFrequency is either f
(C/T2 = 1).
If EXEN2 = 1, a 16-bit reload can be triggered either by an overflow or by a 1-to-0
transition at input T2EX. This transition also sets the EXF2 bit. The Timer 2 interrupt, if
enabled, can be generated when either TF2 or EXF2 is ‘1’.
Microcontroller’s hardware will need three consecutive machine cycles in order to
recognize falling edge on T2EX and set EXF2 = 1: in the first machine cycle pin T2EX has
to be sampled as ‘1’; in the second machine cycle it has to be sampled as ‘0’, and in the
third machine cycle EXF2 will be set to ‘1’.
In
T2EX to control the direction of count. When a logic ‘1’ is applied at pin T2EX Timer 2 will
count up. Timer 2 will overflow at 0FFFFH and set the TF2 flag, which can then generate
an interrupt, if the interrupt is enabled. This timer overflow also causes the 16-bit value in
RCAP2L and RCAP2H to be reloaded into the timer registers TL2 and TH2.
------------------------------------------------------------------------------- -
65536
transition
detector
Figure
SupplyFrequency
C/T2 = 0
C/T2 = 1
14, DCEN = 1 and Timer 2 is enabled to count up or down. This mode allows pin
RCAP2H RCAP2L
EXEN2
control
Rev. 05 — 12 November 2009
TR2
control
reload
osc
RCAP2L RCAP2H
(8-bits)
TL2
(C/T2 = 0) or frequency of signal on T2 pin
(8-bits)
P89V51RB2/RC2/RD2
TH2
8-bit microcontrollers with 80C51 core
EXF2
TF2
© NXP B.V. 2009. All rights reserved.
002aaa524
interrupt
timer 2
34 of 80
(1)