LPC2104FBD48/01,15 NXP Semiconductors, LPC2104FBD48/01,15 Datasheet - Page 16

• Manufacturer Part Number: LPC2104FBD48/01,15
• Description: IC ARM7 MCU FLASH 128K 48-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2100r

Specifications of LPC2104FBD48/01,15

• Program Memory Type: FLASH
• Program Memory Size: 128KB (128K x 8)
• Package / Case: 48-LQFP
• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 60MHz
• Connectivity: I²C, Microwire, SPI, SSI, SSP, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 32
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: LPC21
• Core: ARM7TDMI-S
• Data Bus Width: 16 bit, 32 bit
• Data Ram Size: 16 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 60 MHz
• Number Of Programmable I/os: 32
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: MDK-ARM, RL-ARM, ULINK2, KSK-LPC2106-PL
• Minimum Operating Temperature: - 40 C
• Package: 48LQFP
• Device Core: ARM7TDMI-S
• Family Name: LPC2000
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 1.8|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 568-4310 - EVAL BOARD LPC2158 W/LCD568-4297 - BOARD EVAL LPC21XX MCB2100622-1005 - USB IN-CIRCUIT PROG ARM7 LPC2K568-1756 - BOARD EVAL FOR LPC210X ARM MCU
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 568-4365; 935286614151; LPC2104FBD48/01-S

NXP Semiconductors
LPC2104_2105_2106_7
Product data sheet
6.10.1 Features
6.9.1 Features
6.9.2 Features added with the Fast GPIO set of registers available on
6.10 UARTs
6.9 General purpose parallel I/O
Table 7.
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Separate
registers allow setting or clearing any number of outputs simultaneously. The value of the
output register may be read back, as well as the current state of the port pins.
LPC2104/2105/2106/01 only
The LPC2104/2105/2106 each contain two UARTs. One UART provides a full modem
control handshake interface, the other provides only transmit and receive data lines.
PINSEL1
25:24
27:26
29:28
31:30
•
•
•
•
•
•
•
•
•
•
•
•
Direction control of individual bits.
Separate control of output set and clear.
All I/O default to inputs after reset.
Fast GPIO registers are relocated to the ARM local bus for the fastest possible I/O
timing, enabling port pin toggling up to 3.5 times faster than earlier LPC2000 devices.
Mask registers allow treating sets of port bits as a group, leaving other bits
unchanged.
All Fast GPIO registers are byte addressable.
Entire port value can be written in one instruction.
Ports are accessible via either the legacy group of registers (GPIOs) or the group of
registers providing accelerated port access (Fast GPIOs).
16 byte Receive and Transmit FIFOs
Register locations conform to 16C550 industry standard
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B
Built-in baud rate generator
Pin function select register 1 (PINSEL1 - 0xE002 C004)
Pin name
P0.28
P0.29
P0.30
P0.31
Rev. 07 — 20 June 2008
Value
0
0
0
0
0
0
0
0
0
1
0
1
0
1
0
1
LPC2104/2105/2106
Function
GPIO Port 0.28
TMS
GPIO Port 0.29
TCK
GPIO Port 0.30
TDI
GPIO Port 0.31
TDO
Single-chip 32-bit microcontrollers
…continued
© NXP B.V. 2008. All rights reserved.
Value after
reset
0
0
0
0
16 of 41