ST72F262G1M6 STMicroelectronics, ST72F262G1M6 Datasheet - Page 17

• Manufacturer Part Number: ST72F262G1M6
• Description: MCU 8BIT 4KB FLASH 28-SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F262G1M6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-SOIC (7.5mm Width)
• Controller Family/series: ST7
• No. Of I/o's: 22
• Ram Memory Size: 256Byte
• Cpu Speed: 8MHz
• No. Of Timers: 2
• Embedded Interface Type: I2C, SCI, SPI
• Rohs Compliant: Yes
• Processor Series: ST72F2x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: I2C, SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 4 bit
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7F264-IND/USB, ST72F34X-SK/RAIS, ST7MDT10-DVP3, ST7MDT10-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit
• For Use With: 497-5046 - KIT TOOL FOR ST7/UPSD/STR7 MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: In Transition
• Other names: 497-5581-5

5 CENTRAL PROCESSING UNIT
5.1 INTRODUCTION
This CPU has a full 8-bit architecture and contains
six internal registers allowing efficient 8-bit data
manipulation.
5.2 MAIN FEATURES
■
■
■
■
■
■
■
■
Figure 7. CPU Registers
Enable executing 63 basic instructions
Fast 8-bit by 8-bit multiply
17 main addressing modes (with indirect
addressing mode)
Two 8-bit index registers
16-bit stack pointer
Low power HALT and WAIT modes
Priority maskable hardware interrupts
Non-maskable software/hardware interrupts
RESET VALUE = STACK HIGHER ADDRESS
RESET VALUE = RESET VECTOR @ FFFEh-FFFFh
15
15
RESET VALUE = 1
PCH
8 7
8
RESET VALUE = XXh
RESET VALUE = XXh
RESET VALUE = XXh
7
7
7
1
7
7
1 1 X 1 X X
1 I1 H I0 N Z
PCL
0
0
0
0
X
0
0
C
5.3 CPU REGISTERS
The 6 CPU registers shown in
present in the memory mapping and are accessed
by specific instructions.
Accumulator (A)
The Accumulator is an 8-bit general purpose reg-
ister used to hold operands and the results of the
arithmetic and logic calculations and to manipulate
data.
Index Registers (X and Y)
These 8-bit registers are used to create effective
addresses or as temporary storage areas for data
manipulation. (The Cross-Assembler generates a
precede instruction (PRE) to indicate that the fol-
lowing instruction refers to the Y register.)
The Y register is not affected by the interrupt auto-
matic procedures.
Program Counter (PC)
The program counter is a 16-bit register containing
the address of the next instruction to be executed
by the CPU. It is made of two 8-bit registers PCL
(Program Counter Low which is the LSB) and PCH
(Program Counter High which is the MSB).
ACCUMULATOR
X INDEX REGISTER
Y INDEX REGISTER
PROGRAM COUNTER
CONDITION CODE REGISTER
STACK POINTER
ST72260Gx, ST72262Gx, ST72264Gx
X = Undefined Value
Figure 7
are not
17/172