MC9S08SH4CTJ Freescale Semiconductor, MC9S08SH4CTJ Datasheet - Page 80

• Manufacturer Part Number: MC9S08SH4CTJ
• Description: IC MCU 8BIT 4K FLASH 20-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08SH4CTJ

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, LIN, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 17
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 20-TSSOP
• Processor Series: S08SH
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 17
• Number Of Timers: 3
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08SG32, DEMO9S08SG32AUTO, DEMO9S08SG8, DEMO9S08SG8AUTO, DEMO9S08SH32, DEMO9S08SH8
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• A/d Bit Size: 10 bit
• A/d Channels Available: 12
• Height: 1.05 mm
• Length: 6.6 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.7 V
• Width: 4.5 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

1
Chapter 6 Parallel Input/Output Control
6.6.1
Port A is controlled by the registers listed below.
The pins PTA4 and PTA5 are unique. PTA4 is output-only, so the control bits for the input function will
not have any effect on this pin. PTA5, when configured as an output, is open drain with low drive strength.
6.6.1.1
80
PTAD[5:0]
Reset:
Reads of bit PTAD4 always return the contents of PTAD4, regardless of the value stored in bit PTADD4.
Field
5:0
W
R
Port A Registers
Port A Data Register Bits — For port A pins that are inputs, reads return the logic level on the pin. For port A
pins that are configured as outputs, reads return the last value written to this register.
Writes are latched into all bits of this register. For port A pins that are configured as outputs, the logic level is
driven out the corresponding MCU pin.
Reset forces PTAD to all 0s, but these 0s are not driven out the corresponding pins because reset also configures
all port pins as high-impedance inputs with pull-ups/pull-downs disabled.
Port A Data Register (PTAD)
0
0
7
This PTA5 pin does not contain a clamp diode to V
driven above V
When the internal pullup device is enabled on PTA5 when used as an input
or open drain output the voltage measured on PTA5 will not be pulled to
V
pin is required to drive to a V
DD
. The internal gates connected to this pin are pulled to V
0
0
6
DD
Table 6-2. PTAD Register Field Descriptions
.
Figure 6-3. Port A Data Register (PTAD)
MC9S08SH8 MCU Series Data Sheet, Rev. 3
PTAD5
0
5
DD
PTAD4
level an external pullup should be used.
NOTE
0
4
1
Description
PTAD3
3
0
DD
and should not be
PTAD2
DD
0
2
. If the PTA5
Freescale Semiconductor
PTAD1
0
1
PTAD0
0
0