AT90USB162-16MUR Atmel, AT90USB162-16MUR Datasheet - Page 198

• Manufacturer Part Number: AT90USB162-16MUR
• Description: IC AVR MCU 16K FLASH 32QFN
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB162-16MUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, PS/2, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFN
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, USART, debugWIRE
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600-TQFP32 - STK600 SOCKET/ADAPTER 32-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAGATSTK526 - KIT STARTER FOR AT90USB82/162ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK525 - KIT STARTER FOR AT90USBAT90USBKEY2 - KIT DEMO FOR AT90USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details
• Other names: AT90USB162-16MURTR; AT90USB162-16MUTR; AT90USB162-16MUTR

20.7
198
Address Setup
AT90USB82/162
Figure 20-2. Endpoint activation flow:
As long as the endpoint is not correctly configured (CFGOK cleared), the hardware does not
acknowledge the packets sent by the host.
CFGOK will not be set if the Endpoint size parameter is bigger than the DPRAM size.
A clear of EPEN acts as an endpoint reset (see Section 20.3, page 196 for more details). It also
performs the next operation:
See Section 19.6, page 190 for more details about the memory allocation/reorganization.
The USB device address is set up according to the USB protocol:
ADDEN and UADD shall not be written at the same time.
UADD contains the default address 00h after a power-up or an USB reset.
• The configuration of the endpoint is kept (EPSIZE, EPBK, ALLOC kept)
• It resets the data toggle field.
• The DPRAM memory associated to the endpoint is still reserved.
• the USB device, after power-up, responds at address 0
• the host sends a SETUP command (SET_ADDRESS(addr)),
• the firmware records that address in UADD, but keep ADDEN cleared,
• the USB device sends an IN command of 0 bytes (IN 0 Zero Length Packet) to acknowledge
• then, the firmware may enable the USB device address by setting ADDEN. The only
the transaction,
accepted address by the controller is the one stored in UADD.
Endpoint activated
Yes
UECFG0X
UECFG1X
CFGOK=1
Activation
Endpoint
EPEN=1
UENUM
EPNUM=x
EPTYPE
EPSIZE
ALLOC
EPDIR
EPBK
...
No
ERROR
Select the endpoint
Activate the endpoint
Configure:
Configure:
Allocation and reorganization of
the memory is made on-the-fly
Test the correct endpoint
configuration
- the endpoint direction
- the endpoint type
- the Not Yet Disable feature
- the endpoint size
- the bank parametrization
7707F–AVR–11/10