ATTINY44A-MMHR Atmel, ATTINY44A-MMHR Datasheet - Page 140
ATTINY44A-MMHR
Manufacturer Part Number
ATTINY44A-MMHR
Description
MCU AVR 4KB FLASH 20MHZ 20QFN
Manufacturer
Atmel
Series
AVR® ATtinyr
Specifications of ATTINY44A-MMHR
Core Processor
AVR
Core Size
8-Bit
Speed
20MHz
Connectivity
USI
Peripherals
Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
Number Of I /o
12
Program Memory Size
4KB (2K x 16)
Program Memory Type
FLASH
Eeprom Size
256 x 8
Ram Size
256 x 8
Voltage - Supply (vcc/vdd)
1.8 V ~ 5.5 V
Data Converters
A/D 8x10b
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 140 of 286
- Download datasheet (10Mb)
16.9
16.10 ADC Accuracy Definitions
140
Noise Canceling Techniques
ATtiny24A/44A/84A
In order to avoid distortion from unpredictable signal convolution, signal components higher than
the Nyquist frequency (f
quency components with a low-pass filter before applying the signals as inputs to the ADC.
Figure 16-8.
Note:
Digital circuitry inside and outside the device generates EMI which might affect the accuracy of
analog measurements. When conversion accuracy is critical, the noise level can be reduced by
applying the following techniques:
Where high ADC accuracy is required it is recommended to use ADC Noise Reduction Mode, as
described in
is above 1 MHz, or when the ADC is used for reading the internal temperature sensor, as
described in
bypass capacitors does reduce the need for using ADC Noise Reduction Mode
An n-bit single-ended ADC converts a voltage linearly between GND and V
(LSBs). The lowest code is read as 0, and the highest code is read as 2
Several parameters describe the deviation from the ideal behavior, as follows:
• Keep analog signal paths as short as possible.
• Make sure analog tracks run over the analog ground plane.
• Keep analog tracks well away from high-speed switching digital tracks.
• If any port pin is used as a digital output, it mustn’t switch while a conversion is in progress.
• Place bypass capacitors as close to V
The capacitor in the figure depicts the total capacitance, including the sample/hold capacitor and
any stray or parasitic capacitance inside the device. The value given is worst case.
ADCn
Section 16.7 on page
Section 16.12 on page
Analog Input Circuitry
ADC
/2) should not be present. The user is advised to remove high fre-
I
IH
139. This is especially the case when system clock frequency
I
IL
143. A good system design with properly placed, external
CC
and GND pins as possible.
1..100 kohm
C
S/H
= 14 pF
n
-1.
V
CC
REF
/2
8183C–AVR–03/11
in 2
n
steps
Related parts for ATTINY44A-MMHR
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
Atmel Corporation
Datasheet:
Part Number:
Description:
IC MCU AVR 4K FLASH 20MHZ 14SOIC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MCU AVR 4K FLASH 20MHZ 20QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 4KB FLASH 20MHZ 14SOIC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MCU AVR 4K FLASH 20MHZ 14PDIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 4KB FLASH 20MHZ 15UFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 4KB FLASH 20MHZ 20QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 4KB FLASH 20MHZ 20VQFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
IC MCU AVR 4KB FLASH 20MHZ 14SOI
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 2KB FLASH 20MHZ 16-UFBGA
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU AVR 2KB FLASH 20MHZ 14-SOIC
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
8-bit Microcontrollers - MCU 4KB FL 256B EE 256B SRAM 20MHz Hi +125C
Manufacturer:
Atmel
Part Number:
Description:
8-bit Microcontrollers - MCU 4KB FL 256B EE 256B SRAM 20MHz Hi +125C
Manufacturer:
Atmel