AT89LP216-20PU Atmel, AT89LP216-20PU Datasheet - Page 24

• Manufacturer Part Number: AT89LP216-20PU
• Description: MCU 8051 2K FLASH 20MHZ 16-PDIP
• Manufacturer: Atmel
• Series: 89LPr

Specifications of AT89LP216-20PU

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 14
• Program Memory Size: 2KB (2K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.4 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-DIP (0.300", 7.62mm)
• Processor Series: AT89x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 128 B
• Interface Type: UART, SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 14
• Number Of Timers: 2
• Operating Supply Voltage: 2.4 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: AT89ISP
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Details

13.1.2
13.1.3
13.1.4
24
AT89LP216
Input-only Mode
Open-drain Output
Push-pull Output
The input only port configuration is shown in
input includes a Schmitt-triggered input for improved input noise rejection. The input circuitry of
P1.3, P3.2 and P3.3 is not disabled during Power-down (see
safely driven to 5.5V even when operating at lower V
the Schmitt trigger will be set by the V
Figure 13-2. Input Only
Figure 13-3. Input Only for P1.3, P3.2 and P3.3
The open-drain output configuration turns off all pull-ups and only drives the pull-down transistor
of the port pin when the port latch contains a logic “0”. To be used as a logic output, a port con-
figured in this manner must have an external pull-up, typically a resistor tied to V
down for this mode is the same as for the quasi-bidirectional mode. The open-drain port configu-
ration is shown in
Power-down (see
operating at lower V
the V
Figure 13-4. Open-drain Output
The push-pull output configuration has the same pull-down structure as both the open-drain and
the quasi-bidirectional output modes, but provides a continuous strong pull-up when the port
latch contains a logic “1”. The push-pull mode may be used when more source current is needed
from a port output. Note that due to the 5V tolerant architecture, the push-pull output will have
reduced output high levels at DC operation and hot temperature. Under AC operation an inte-
grated boost circuit provides more source current. The push-pull port configuration is shown in
Figure
Figure
CC
13-5. The input circuitry of P1.3, P3.2 and P3.3 is not disabled during Power-down (see
13-3).
Register
From Port
level and must be taken into consideration.
Input
Data
Figure
Figure
Input
Data
CC
PWD
levels; however, the input threshold of the Schmitt trigger will be set by
13-4.The input circuitry of P1.3, P3.2 and P3.3 is not disabled during
13-3). Open-drain pins can be safely pulled high to 5.5V even when
CC
level and must be taken into consideration.
Figure
Input
Data
PWD
13-2. The output drivers are tristated. The
CC
levels; however, the input threshold of
Port
Pin
Port
Pin
Figure
13-3). Input pins can be
3621E–MICRO–11/10
CC
Port
Pin
. The pull-