ATTINY43U-SUR Atmel, ATTINY43U-SUR Datasheet - Page 127

• Manufacturer Part Number: ATTINY43U-SUR
• Description: MCU AVR 4KB FLASH 8MHZ 20SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY43U-SUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

16.13.2
8048B–AVR–03/09
ADCSRA – ADC Control and Status Register A
• Bits 2:0 – MUX[2:0]: Analog Channel Selection Bits
The value of these bits selects which analog input is connected to the ADC, as shown in
16-4. Selecting channel ADC4 enables temperature measurement.
Table 16-4.
Notes:
If these bits are changed during a conversion, the change will not go into effect until this
conversion is complete (ADIF in ADCSRA is set).
• Bit 7 – ADEN: ADC Enable
Writing this bit to one enables the ADC. By writing it to zero, the ADC is turned off. Turning the
ADC off while a conversion is in progress, will terminate this conversion.
• Bit 6 – ADSC: ADC Start Conversion
In Single Conversion mode, write this bit to one to start each conversion. In Free Running mode,
write this bit to one to start the first conversion. The first conversion after ADSC has been written
after the ADC has been enabled, or if ADSC is written at the same time as the ADC is enabled,
will take 25 ADC clock cycles instead of the normal 13. This first conversion performs initializa-
tion of the ADC.
ADSC will read as one as long as a conversion is in progress. When the conversion is complete,
it returns to zero. Writing zero to this bit has no effect.
• Bit 5 – ADATE: ADC Auto Trigger Enable
When this bit is written to one, Auto Triggering of the ADC is enabled. The ADC will start a con-
version on a positive edge of the selected trigger signal. The trigger source is selected by setting
the ADC Trigger Select bits, ADTS in ADCSRB.
Bit
0x06 (0x26)
Read/Write
Initial Value
1. Due to the voltage divider present, a current will flow from V
2. See
divider as long as this channel is selected.
ADC Multiplexer Channel Selections.
“Temperature Measurement” on page
ADEN
R/W
7
0
Single Ended Input
ADC0 (PA0)
ADC1 (PA1)
ADC2 (PA2)
ADC3 (PA3)
ADSC
1.1V (I Ref)
R/W
0V (GND)
ADC4
6
0
V
BAT
(1)
(2)
ADATE
R/W
5
0
ADIF
R/W
4
0
125.
ADIE
R/W
3
0
ADPS2
R/W
2
0
BAT
to ground via a 100kΩ resistor
ADPS1
R/W
1
0
MUX[2:0]
000
001
010
011
100
101
110
111
ADPS0
R/W
0
0
ADCSRA
Table
127