ATTINY43U-SUR Atmel, ATTINY43U-SUR Datasheet - Page 60

• Manufacturer Part Number: ATTINY43U-SUR
• Description: MCU AVR 4KB FLASH 8MHZ 20SOIC
• Manufacturer: Atmel
• Series: AVR® ATtinyr

Specifications of ATTINY43U-SUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: USI
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 4KB (2K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 64 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

10.3.2
10.3.3
60
ATtiny43U
GIMSK – General Interrupt Mask Register
GIFR – General Interrupt Flag Register
If low level interrupt is selected, the low level must be held until the completion of the currently
executing instruction to generate an interrupt.
Table 10-2.
• Bits 7, 3:0 – Res: Reserved Bits
These bits are reserved and will always read zero.
• Bit 6 – INT0: External Interrupt Request 0 Enable
When the INT0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), the exter-
nal pin interrupt is enabled. The Interrupt Sense Control0 bits 1/0 (ISC01 and ISC00) in the MCU
Control Register (MCUCR) define whether the external interrupt is activated on rising and/or fall-
ing edge of the INT0 pin or level sensed. Activity on the pin will cause an interrupt request even
if INT0 is configured as an output. The corresponding interrupt of External Interrupt Request 0 is
executed from the INT0 Interrupt Vector.
• Bit 5 – PCIE1: Pin Change Interrupt Enable 1
When the PCIE1 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin
change interrupt 1 is enabled. Any change on any enabled PCINT15..8 pin will cause an inter-
rupt. The corresponding interrupt of Pin Change Interrupt Request is executed from the PCI1
Interrupt Vector. PCINT15..8 pins are enabled individually by the PCMSK1 Register.
• Bit 4 – PCIE0: Pin Change Interrupt Enable 0
When the PCIE0 bit is set (one) and the I-bit in the Status Register (SREG) is set (one), pin
change interrupt 0 is enabled. Any change on any enabled PCINT7..0 pin will cause an interrupt.
The corresponding interrupt of Pin Change Interrupt Request is executed from the PCI0 Inter-
rupt Vector. PCINT7..0 pins are enabled individually by the PCMSK0 Register.
• Bits 7, 3:0 – Res: Reserved Bits
These bits are reserved and will always read zero.
Bit
0x3B (0x5B)
Read/Write
Initial Value
Bit
0x3A (0x5A)
Read/Write
Initial Value
ISC01
0
0
1
1
Interrupt 0 Sense Control
ISC00
R
R
7
–
0
7
–
0
0
1
0
1
INTF0
INT0
R/W
R/W
Description
The low level of INT0 generates an interrupt request asynchronously
Any logical change on INT0 generates an interrupt request asynchronously
The falling edge of INT0 generates an interrupt request asynchronously
The rising edge of INT0 generates an interrupt request asynchronously
6
0
6
0
PCIE1
PCIF1
R/W
R/W
5
0
5
0
PCIE0
PCIF0
R/W
R/W
4
0
4
0
R
R
3
–
0
3
–
0
R
R
2
–
0
2
–
0
R
R
1
–
0
1
–
0
0
–
R
0
0
–
R
0
8048B–AVR–03/09
GIMSK
GIFR