PIC16F688-I/P Microchip Technology, PIC16F688-I/P Datasheet - Page 128

• Manufacturer Part Number: PIC16F688-I/P
• Description: IC PIC MCU FLASH 4KX14 14DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F688-I/P

• Program Memory Type: FLASH
• Program Memory Size: 7KB (4K x 14)
• Package / Case: 14-DIP (0.300", 7.62mm)
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: UART/USART
• Peripherals: Brown-out Detect/Reset, POR, WDT
• Number Of I /o: 12
• Eeprom Size: 256 x 8
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC16F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SCI/USART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 2
• Operating Supply Voltage: 2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, DM163014, DM164120-4
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Data Rom Size: 256 B
• Height: 3.3 mm
• Length: 19.05 mm
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2 V
• Width: 6.35 mm
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC162066 - HEADER INTRFC MPLAB ICD2 20PINAC162061 - HEADER INTRFC MPLAB ICD2 20PINDM163029 - BOARD PICDEM FOR MECHATRONICSAC162056 - HEADER INTERFACE ICD2 16F688ACICE0207 - MPLABICE 14P 300 MIL ADAPTERAC124001 - MODULE SKT PROMATEII 8DIP/SOIC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC16F688
FIGURE 11-10:
11.7
If
programmed, the on-chip program memory can be
read out using ICSP for verification purposes.
11.8
Four memory locations (2000h-2003h) are designated
as ID locations where the user can store checksum or
other code identification numbers. These locations are
not accessible during normal execution but are
readable and writable during Program/Verify mode.
Only the Least Significant 7 bits of the ID locations are
used.
DS41203E-page 126
Instruction Flow
(INTCON<1>)
(INTCON<7>)
Note
Note:
INTF flag
GIE bit
Instruction
Fetched
Instruction
Executed
the
CLKOUT
INT pin
OSC1
1:
2:
3:
4:
Code Protection
ID Locations
code
PC
(4)
The entire data EEPROM and Flash
program memory will be erased when the
code protection is turned off. See the
“PIC12F6XX/16F6XX Memory Program-
ming Specification” (DS41204) for more
information.
XT, HS or LP Oscillator mode assumed.
T
GIE = 1 assumed. In this case after wake-up, the processor jumps to 0004h. If GIE = 0, execution will continue in-line.
CLKOUT is not available in XT, HS, LP or EC Oscillator modes, but shown here for timing reference.
OST
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1
Inst(PC) = Sleep
protection
Inst(PC - 1)
= 1024 T
PC
WAKE-UP FROM SLEEP THROUGH INTERRUPT
OSC
(drawing not to scale). This delay does not apply to EC and RC Oscillator modes.
bit(s)
Inst(PC + 1)
Sleep
PC + 1
have
Processor in
not
Sleep
PC + 2
been
T
OST (2)
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Interrupt Latency
Inst(PC + 2)
Inst(PC + 1)
PC + 2
(3)
Dummy Cycle
PC + 2
© 2009 Microchip Technology Inc.
Dummy Cycle
Inst(0004h)
0004h
Inst(0005h)
Inst(0004h)
0005h