AT90PWM3B-16SUR Atmel, AT90PWM3B-16SUR Datasheet - Page 113

• Manufacturer Part Number: AT90PWM3B-16SUR
• Description: MCU AVR 8K FLASH 16MHA 32SOIC
• Manufacturer: Atmel
• Series: AVR® 90PWM Lightingr

Specifications of AT90PWM3B-16SUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 27
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 32-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

15.7.1
15.8
4317J–AVR–08/10
Modes of Operation
Compare Output Mode and Waveform Generation
Figure 15-5. Compare Match Output Unit, Schematic
The general I/O port function is overridden by the Output Compare (OCnx) from the Waveform
Generator if either of the COMnx1:0 bits are set. However, the OCnx pin direction (input or out-
put) is still controlled by the Data Direction Register (DDR) for the port pin. The Data Direction
Register bit for the OCnx pin (DDR_OCnx) must be set as output before the OCnx value is visi-
ble on the pin. The port override function is generally independent of the Waveform Generation
mode, but there are some exceptions. Refer to
details.
The design of the Output Compare pin logic allows initialization of the OCnx state before the out-
put is enabled. Note that some COMnx1:0 bit settings are reserved for certain modes of
operation.
The COMnx1:0 bits have no effect on the Input Capture unit.
The Waveform Generator uses the COMnx1:0 bits differently in normal, CTC, and PWM modes.
For all modes, setting the COMnx1:0 = 0 tells the Waveform Generator that no action on the
OCnx Register is to be performed on the next compare match. For compare output actions in the
non-PWM modes refer to
page
page
A change of the COMnx1:0 bits state will have effect at the first compare match after the bits are
written. For non-PWM modes, the action can be forced to have immediate effect by using the
FOCnx strobe bits.
The mode of operation, i.e., the behavior of the Timer/Counter and the Output Compare pins, is
defined by the combination of the Waveform Generation mode (WGMn3:0) and Compare Output
mode (COMnx1:0) bits. The Compare Output mode bits do not affect the counting sequence,
COMnx1
COMnx0
FOCnx
123, and for phase correct and phase and frequency correct PWM refer to
123.
clk
I/O
See “16-bit Timer/Counter Register Description” on page 122.
Waveform
Generator
Table 15-2 on page
D
D
D
PORT
DDR
OCnx
123. For fast PWM mode refer to
Q
Q
Q
Table
15-2,
AT90PWM2/3/2B/3B
1
0
Table 15-3
and
Table 15-4
Table 15-3 on
Table 15-4 on
OCnx
Pin
113
for