AT90PWM3B-16SUR Atmel, AT90PWM3B-16SUR Datasheet - Page 230

• Manufacturer Part Number: AT90PWM3B-16SUR
• Description: MCU AVR 8K FLASH 16MHA 32SOIC
• Manufacturer: Atmel
• Series: AVR® 90PWM Lightingr

Specifications of AT90PWM3B-16SUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 27
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 11x10b; D/A 1x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 32-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

20.2.4
230
AT90PWM2/3/2B/3B
Analog Comparator Status Register – ACSR
• Bit 6– AC2IE: Analog Comparator 2 Interrupt Enable bit
Set this bit to enable the analog comparator 2 interrupt.
Clear this bit to disable the analog comparator 2 interrupt.
• Bit 5, 4– AC2IS1, AC2IS0: Analog Comparator 2 Interrupt Select bit
These 2 bits determine the sensitivity of the interrupt trigger.
The different setting are shown in
Table 20-5.
• Bit 2, 1, 0– AC2M2, AC2M1, AC2M0: Analog Comparator 2 Multiplexer register
These 3 bits determine the input of the negative input of the analog comparator.
The different setting are shown in
Table 20-6.
Bit
Read/Write
Initial Value
• Bit 7– ACCKDIV: Analog Comparator Clock Divider
The analog comparators can work with a clock up to 8MHz@3V and 16MHz@5V.
Set this bit in case the clock frequency of the microcontroller is higher than 8 MHz to insert a
divider by 2 between the clock of the microcontroller and the clock of the analog comparators.
Clear this bit to have the same clock frequency for the microcontroller and the analog
comparators.
• Bit 6– AC2IF: Analog Comparator 2 Interrupt Flag Bit
This bit is set by hardware when comparator 2 output event triggers off the interrupt mode
defined by AC2IS1 and AC2IS0 bits in AC2CON register.
This bit is cleared by hardware when the corresponding interrupt vector is executed in case the
AC2IS1
0
0
1
1
AC2M2
0
0
0
0
1
1
1
1
Interrupt sensitivity selection
Analog Comparator 2 negative input selection
ACCKDIV
AC2IS0
0
1
0
1
AC2M1
0
0
1
1
0
0
1
1
R/W
7
0
AC2IF
R/W
6
0
Description
Comparator Interrupt on output toggle
Reserved
Comparator interrupt on output falling edge
Comparator interrupt on output rising edge
AC2M0
0
1
0
1
0
1
0
1
AC1IF
Table
Table
R/W
5
0
20-1.
20-6.
Description
“Vref”/6.40
“Vref”/3.20
“Vref”/2.13
“Vref”/1.60
Analog Comparator Negative Input (ACMPM pin)
DAC result
Reserved
Reserved
AC0IF
R/W
4
0
3
0
-
-
AC2O
R
2
0
AC1O
R
1
0
AC0O
R
0
0
4317J–AVR–08/10
ACSR