PIC18F45K20-I/ML Microchip Technology, PIC18F45K20-I/ML Datasheet - Page 71

• Manufacturer Part Number: PIC18F45K20-I/ML
• Description: IC PIC MCU FLASH 16KX16 44QFN
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F45K20-I/ML

• Program Memory Type: FLASH
• Program Memory Size: 32KB (16K x 16)
• Package / Case: 44-QFN
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 35
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 14x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 1.5 KB
• Interface Type: CCP/ECCP/EUSART/I2C/MSSP/SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Programmable I/os: 36
• Number Of Timers: 4
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 14-ch x 10-bit
• Package: 44QFN EP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 64 MHz
• Operating Supply Voltage: 2.5|3.3 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DM240313 - BOARD DEMO 8BIT XLPAC164112 - VOLTAGE LIMITER MPLAB ICD2 VPPDM164124 - KIT STARTER FOR PIC18F4XK20AC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

FIGURE 3-56:
FIGURE 3-57:
© 2009 Microchip Technology Inc.
Step into the following statement and through the function, which erases a 64-byte
block of memory that the strings are stored in.
After completing the erase, select menu Debugger > Read. In the Program Memory
window, the 64 bytes of program memory starting at address 0x0100 where the strings
were stored have been erased, as shown in Figure 3-56.
ERASED 0X0100 TO 0X013F
The remaining code creates a 32-byte buffer in RAM and fills it with the alphabet
characters in uppercase, plus a few punctuation characters at the end. This buffer is
then written to the 32-byte block of program memory starting at 0x0100 that was just
erased. Since we read program memory, we’ll have to reset the debugger. Select
Debugger > Reset > Processor Reset. Right-click on the source code and select
Breakpoints > Remove All Breakpoints from the pop-up menu to clear the breakpoint
we set earlier. Run the program. After running for a few seconds, select Debugger >
Halt. The program should be stopped at final while(1) loop. Select Debugger > Read
again and we can see that the write to program memory was successful.
PROGRAM MEMORY WRITE RESULTS
// Erase the 64 bytes starting at 0x100
ProgMemErase64(0x100);
PICkit™ 3 Debug Express Lessons
DS41370C-page 67