PIC18F87J11T-I/PT Microchip Technology, PIC18F87J11T-I/PT Datasheet - Page 8

• Manufacturer Part Number: PIC18F87J11T-I/PT
• Description: IC PIC MCU FLASH 64KX16 80TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F87J11T-I/PT

• Core Size: 8-Bit
• Program Memory Size: 128KB (64K x 16)
• Oscillator Type: Internal
• Core Processor: PIC
• Speed: 48MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 68
• Program Memory Type: FLASH
• Ram Size: 3930 x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 15x10b
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TFQFP
• Controller Family/series: PIC18
• No. Of I/o's: 68
• Ram Memory Size: 3930Byte
• Cpu Speed: 48MHz
• No. Of Timers: 5
• No. Of Pwm: RoHS Compliant
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 3904 B
• Interface Type: EUSART, I2C, MSSP, SPI
• Maximum Clock Frequency: 48 MHz
• Number Of Programmable I/os: 68
• Number Of Timers: 5
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM183032, DM183022, DV164136
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 15 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DV164136 - DEVELOPMENT KIT FOR PIC18AC162091 - HEADER MPLAB ICD2 18F87J11 64/80MA180020 - MODULE PLUG-IN HPC EXPL 18F87J11AC164328 - MODULE SKT FOR 80TQFP
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: PIC18F87J11T-I/PTTR

PIC18F6XJXX/8XJXX
2.3
Figure 2-6 shows the high-level overview of the
programming process. First, a Bulk Erase is performed.
Next, the code memory is programmed. Since the only
nonvolatile Configuration Words are within the code
memory space, they too are programmed as if they
were code. Code memory (including the Configuration
Words) is then verified to ensure that programming was
successful.
FIGURE 2-6:
FIGURE 2-7:
DS39644E-page 8
Note:
MCLR
V
PGD
PGC
DD
Overview of the Programming
Process
In order to maintain the endurance of the
cells, each Flash byte should not be
programmed more then twice between
erase operations. A Bulk Erase of the
device is required before attempting to
modify the contents a third time.
Program Memory
Verify Program
Enter ICSP™
Perform Bulk
P13
HIGH-LEVEL
PROGRAMMING FLOW
ENTERING PROGRAM/VERIFY MODE
Exit ICSP
Erase
Done
Start
P1
P19
V
b31
IH
0
b30
1
Program/Verify Entry Code = 4D434850h
b29
0
b28
P2B
0
P2A
b27
2.4
Entry into ICSP modes for PIC18F6XJXX/8XJXX
devices is somewhat different than previous PIC18
devices. As shown in Figure 2-7, entering ICSP
Program/Verify mode requires three steps:
1.
2.
3.
The programming voltage applied to MCLR is V
essentially, V
for holding at V
least P19 must elapse before presenting the key
sequence on PGD.
The key sequence is a specific 32-bit pattern,
‘0100 1101 0100 0011 0100 1000 0101 0000’
(more easily remembered as 4D434850h in hexa-
decimal). The device will enter Program/Verify mode
only if the sequence is valid. The Most Significant bit of
the most significant nibble must be shifted in first.
Once the key sequence is complete, V
applied to MCLR and held at that level for as long as
Program/Verify mode is to be maintained. An interval of
at least time P20 and P12 must elapse before present-
ing data on PGD. Signals appearing on PGD before
P12 has elapsed will not be interpreted as valid.
On successful entry, the program memory can be
accessed and programmed in serial fashion. While in
the Program/Verify mode, all unused I/Os are placed in
the high-impedance state.
Exiting Program/Verify mode is done by removing V
from MCLR, as shown in Figure 2-8. The only require-
ment for exit is that an interval P16 should elapse
between the last clock and the program signals on
PGC and PGD before removing V
1
...
Voltage is briefly applied to the MCLR pin.
A 32-bit key sequence is presented on PGD.
Voltage is reapplied to MCLR within a specific
period of time and held.
Entering and Exiting ICSP
Program/Verify Mode
b3
0
DD
IH
. There is no minimum time requirement
b2
. After V
0
b1
0
V
© 2006 Microchip Technology Inc.
IH
IH
is removed, an interval of at
b0
0
P20
IH
.
P12
IH
must be
IH
, or
IH