AT90USB162-16MU Atmel, AT90USB162-16MU Datasheet - Page 264

• Manufacturer Part Number: AT90USB162-16MU
• Description: MCU AVR USB 16K FLASH 32-QFN
• Manufacturer: Atmel
• Series: AVR® 90USBr

Specifications of AT90USB162-16MU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: EBI/EMI, PS/2, SPI, UART/USART, USB
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 22
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-TQFN
• Controller Family/series: AVR USB
• No. Of I/o's: 22
• Eeprom Memory Size: 512Byte
• Ram Memory Size: 512Byte
• Cpu Speed: 16MHz
• Rohs Compliant: Yes
• Processor Series: AT90USBx
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: SPI, USART, debugWIRE
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 22
• Number Of Timers: 2
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATSTK525, ATSTK526, ATAVRISP2, ATAVRONEKIT, AT90USBKEY, ATEVK525
• Minimum Operating Temperature: - 40 C
• For Use With: ATSTK600 - DEV KIT FOR AVR/AVR32ATSTK526 - KIT STARTER FOR AT90USB82/162ATAVRDRAGON - KIT DRAGON 32KB FLASH MEM AVRATSTK525 - KIT STARTER FOR AT90USBAT90USBKEY2 - KIT DEMO FOR AT90USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Data Converters: -
• Lead Free Status / Rohs Status: Details

26.3
26.4
264
4. Although each I/O port can source more than the test conditions (20mA at VCC = 5V, 10mA at VCC = 3V) under steady
5. All DC Characteristics contained in this datasheet are based on simulation and characterization of other AVR microcon-
6. Values with “Power Reduction Register 1 - PRR1” disabled (0x00).
7. As specified in the USB Electrical chapter, the D+/D- pads can withstand voltages down to -1V applied through a 39Ω resis-
8. All IOs Except XTAL1, MOSI, MISO, PS2 and Reset pins
External Clock Drive Waveforms
External Clock Drive
AT90USB82/162
1.)The sum of all IOL, for ports B0-B7, C0-C7, D0-D7 should not exceed 150 mA.
If IOL exceeds the test condition, VOL may exceed the related specification. Pins are not guaranteed to sink current greater
than the listed test condition.
state conditions (non-transient), the following must be observed:
1.)The sum of all IOL, for ports B0-B7, C0-C7, D0-D7 should not exceed 150 mA.
If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current
greater than the listed test condition.
trollers manufactured in the same process technology. These values are preliminary values representing design targets, and
will be updated after characterization of actual silicon
tor (in series with the external 22Ω resistor).
Figure 26-1. External Clock Drive Waveforms
Table 26-1.
Note:
Symbol
1/t
Δ
t
t
t
t
t
CHCX
CLCX
CLCH
CHCL
CLCL
t
CLCL
CLCL
All DC Characteristics contained in this datasheet are based on simulation and characterization of
other AVR microcontrollers manufactured in the same process technology. These values are pre-
liminary values representing design targets, and will be updated after characterization of actual
silicon.
Parameter
Oscillator
Frequency
Clock Period
High Time
Low Time
Rise Time
Fall Time
Change in period
from one clock
cycle to the next
External Clock Drive
V
IL1
V
IH1
Min.
V
125
50
50
0
CC
=2.7-5.5V
Max.
1.6
1.6
8
2
V
Min.
62.5
25
25
CC
0
=4.5-5.5V
Max.
0.5
0.5
16
2
Units
MHz
ns
ns
ns
μs
μs
%
7707F–AVR–11/10